Application GPS Glaz has become one of the most popular tools for remote vehicle monitoring among Russian car owners. This solution allows you to track the location of the car in real time, control the speed limit, fuel consumption and even receive notifications about unauthorized engine starts - all via a smartphone on the Android. But how to configure the application correctly, which functions are really useful, and which ones just waste battery power? In this guide we will understand all the nuances of working with GPS Glaz, from installation to solving common problems.

The peculiarity of the service is that it works with most GPS trackers of domestic and Chinese production, including models from StarLine, Pandora, Scher-Khan and other brands. However, not all features are available on all devices; compatibility is important to understand here. For example, tracking fuel levels requires a special sensor, and geofencing only works with a stable Internet connection. Next, we will look in detail at how to avoid common mistakes when setting up and make the most of the application’s capabilities.

What is GPS Glaz and how does it work with a car tracker

GPS Glaz is a mobile application that interacts with a GPS/GSM tracker installed in a car. The principle of operation is simple: the tracker sends data about the location, speed and condition of the car to the server, and the application visualizes this information on a map in real time. It is important to understand that the application itself does not replace the tracker — it only provides an interface for management and monitoring.

Among the key features of the service:

  • 📍 Real-time tracking with coordinates updated every 10–60 seconds (depending on the tracker model).
  • 🚗 Speed control and alerts when a specified limit is exceeded.
  • ⛽ Fuel consumption monitoring (requires additional fuel level sensor).
  • 🔔 Notifications about driving without a key, turning off the power or leaving the geofence.
  • 📊 Route history with the ability to export data to GPX or KML.

The application supports work with trackers using protocols TCP and UDP, as well as most popular commands SMS control (for example, GPRS123456 to request coordinates). However, for full operation the tracker requires a stable connection to the Internet via GSM network (2G/3G/4G depending on model).

⚠️ Attention: Some cheap trackers (for example, models based on a MTK) may conflict with Glaz GPS servers. Before purchasing, check compatibility with the seller or official website.

Step-by-step instructions: how to install and configure GPS Glaz on Android

Installing the app is straightforward, but setting it up correctly requires attention to detail. Follow this algorithm to avoid common mistakes:

  1. Download the app from Google Play (official version) or from the developer's website. Avoid third-party sources - they may distribute modified versions with viruses.
  2. Register an account:
    • Open the application and select Registration.
    • Please indicate valid email (needed to restore access).
    • Create a strong password (at least 8 characters, with numbers and capital letters).
  3. Add a tracker:
    • From the menu, select Add device.
    • Specify IMEI tracker (15-digit code on the device body or in the documentation).
    • Select a model from the list or specify Other, if yours is not there.
  • Configure communication settings:
    • Enter APN your operator (for example, internet.beeline.ru for Beeline).
    • Specify IP address and port server (default gps.glaz.ru:10001).

      • After adding the device, check the connection: a tracker icon with status should appear in the main menu Online. If there is no status or is displayed Offline, go to section problem solving.

      Make sure that the tracker has a SIM card with a positive balance

      Check that the SIM supports data transfer (not all tariffs for trackers include the Internet)

      Enable data transfer via GPRS in the tracker settings (the command is usually GPRS1#)

      Disable power saving mode on your smartphone for GPS Glaz

      -->

      Comparison of GPS Glaz with analogues: which is better for the car owner

      There are several popular transport monitoring applications on the market: Wialon, Navixy, Gurtam and others. To understand if it is suitable GPS Glaz just for you, let’s compare it with its main competitors:

      Criterion GPS Glaz Wialon Navixy
      Cost Free (premium features from RUB 300/month) From 500 ₽/month for the basic tariff From 400 ₽/month
      Tracker support Most Chinese and Russian models Wide list, including professional devices Mainly branded trackers (Teltonika, Queclink)
      Geofences Up to 10 zones in the free version Unlimited Up to 50 zones
      Export data GPX, KML, CSV XLS, PDF, API for integration Excel, Google Sheets
      Features Simple interface, Russian-language support For business fleets, complex setup Good analytics, but expensive

      The critical difference between GPS Glaz and its competitors is its focus on private car owners, and not on businesses. There are no complex reports for accounting or integration with 1C, but there are convenient notifications about speeding or unauthorized movement. If you only need basic monitoring features without breaking the bank, this app is your best choice.

      GPS Glaz|Wialon|Navixy|Other|I don’t use trackers-->

      Advanced features: geofencing, alerts and fuel control

      Basic coordinate tracking is often not enough to fully control the car. Let's look at how to set up the most useful advanced features GPS Glaz:

      1. Geofences (virtual fences)

      Geofences allow you to create virtual boundaries on a map (for example, around your home or office) and receive notifications when a car crosses them. To add a geofence:

      1. Open the map and find the desired location.
      2. Click Add geofence (circle icon).
      3. Set the radius (from 100 m to 5 km).
      4. Select alert type: Login, Exit or Both.

    The maximum number of geofences in the free version is 10. To increase the limit, a premium subscription is required.

    2. Speed control

    The function is useful for parents supervising teenagers behind the wheel, or car fleet owners. Setting:

    • Go to Settings → Notifications → Speed.
    • Set a threshold value (eg 90 km/h).
    • Select notification method: push notification or SMS.

    3. Fuel monitoring

    This feature requires a tracker that supports a fuel level sensor (for example, StarLine M17 or Pandora D-020). Setting:

    • Connect the sensor to the fuel tank.
    • In the application, select Settings → Sensors → Fuel.
    • Enter tank volume and calibration values (if required).
    ⚠️ Attention: Fuel sensors often give an error of up to 5–10% due to the shape of the tank. For accurate measurements, manual calibration is required (fill the tank full and reset the data in the application).
    💡

    If geofence notifications are delayed, check your smartphone's power saving settings. Add GPS Glaz to the list of exceptions for background activity.

    Typical problems and their solutions: why the tracker does not work

    Even with proper configuration, users encounter errors. Let's look at the most common cases and ways to eliminate them:

    1. The tracker is not detected (status "Offline")

    Causes and solutions:

    • 🔋 The tracker battery is low — connect to the charger (if the model supports autonomous operation).
    • 📶 No connection to the network — check your SIM card balance and operator coverage.
    • 🔌 Incorrect APN settings — check the parameters with the operator and enter them manually into Settings → Device → APN.
    • 🔄 Firmware failure — reset the tracker to factory settings (command RESET# via SMS).

    2. Notifications do not arrive

    What to check:

    • 🛠️ Alert Settings - make sure they are turned on Push notifications in the application menu.
    • 📵 Do Not Disturb Mode on a smartphone - add GPS Glaz to the exceptions.
    • 🔕 Block background activity - disable battery optimization for the application (in Android settings).

    3. Inaccurate coordinates

    If the location "jumps" or shows an error of up to 500 m:

    • 📡 Weak GPS signal — the tracker must be in the line of sight of the sky (not in a basement or metal garage).
    • 🔧 Calibration required - run the command GPSFIX# via SMS.
    • 📱 Problems with cards — update the map cache in the application settings.
    How to reset the tracker to factory settings?

    For most models, it is enough to send an SMS with the command RESET123456 (where 123456 is the default password). After the reset, the tracker will return to standard settings and will need to be configured again in GPS Glaz. Check the exact command in the device instructions, as for some brands (for example, Scher-Khan) a different syntax is used, for example FACTORY#.

    Hidden capabilities: what GPS Glaz can do, but not everyone knows

    In addition to basic functions, the application has useful features that are rarely mentioned in official guides:

    • 🔍 Search by history: You can filter routes by date, speed or fuel consumption. For example, to find all trips with a speed above 120 km/h.
    • 📤 Export data for tax purposes: if the machine is used for business purposes, the report is in the format CSV can be submitted to the accounting department to confirm expenses.
    • 🔑 Remote control: some trackers (for example, StarLine M31) allow you to block the engine or turn on the siren directly from the application.
    • 📡 Black box mode: In case of an accident, the tracker saves data 30 seconds before the impact (requires accelerometer support).

      • Another little-known feature is sharing. You can provide temporary access to monitoring to another user (for example, a mechanic at a service station or a relative). To do this:

      1. Go to Settings → Sharing.
      2. Enter the email address of the invitee.
      3. Select rights: View or Management.
      ⚠️ Attention: When shared, another user will be able to see all routes and events. Do not share access with others if you store valuables in your car or if you frequently visit sensitive places (such as banks).
      💡

      The most useful hidden feature is filtering history by speed. This allows you to quickly find all cases of exceeding the speed limit, which is especially important for monitoring young drivers or couriers.

      Security and Privacy: How to Protect Tracker Data

      The use of a GPS tracker raises questions about the security of personal data. Here's what you need to know:

      1. Account protection:

      • Use two-factor authentication (setting in Profile → Security).
      • Don't use simple passwords (eg. 123456 or date of birth).
      • Regularly check the list of devices with access to your account (Settings → Devices).

      2. Tracker protection:

      • Install PIN code to the tracker's SIM card so that attackers cannot send commands via SMS.
      • Hide IMEI tracker - do not publish it in open sources (forums, social networks).
      • Set up an alert about removing the SIM card (if the tracker supports this function).

      3. Legal nuances:

      In Russia, the use of GPS trackers is legal if:

      • you are car owner or have the written consent of the owner.
      • The tracker is not used for spying on people (for example, behind taxi passengers without their knowledge).
      • Data is not transferred to third parties without consent (exception - law enforcement agencies upon request).

      If the tracker is installed in a company car, the employer is obliged to notify the employee about the monitoring (Article 86 of the Labor Code of the Russian Federation).

      FAQ: answers to frequently asked questions about GPS Glaz

      Is it possible to use GPS Glaz without the Internet?

      No, the application requires an Internet connection on your smartphone to work and on the tracker side (via SIM card). However, some trackers (for example, Queclink GV55) can save data to internal memory and transfer it later when the connection is restored.

      How much does the premium version of GPS Glaz cost?

      Tariffs for 2026:

      • Basic — free (limited to 1 tracker and 10 geofences).
      • Standard — 300 ₽/month (up to 3 trackers, 50 geofences, history for 6 months).
      • Professional — 800 ₽/month (unlimited number of trackers, API, advanced analytics).

      Payment is made via Google Pay, bank card or SberPay.

      How to transfer data from GPS Glaz to another application?

      Export history in GPX or KML:

      1. Open History → Export.
      2. Select a period and format.
      3. The file will be saved in the phone memory or sent by email.

      To import to Wialon or Navixy format conversion may be required (use online services like GPX2KML).

      Is it possible to track multiple cars in one account?

      Yes, in the free version - up to 1 tracker, in paid plans - up to 10 or more. To add another device:

      1. Go to Devices → Add.
      2. Specify the IMEI of the new tracker.
      3. Configure communication parameters (APN, server).

      All cars will be displayed on one map with the ability to filter.

      What to do if the tracker was stolen along with the car?

      Urgent actions:

      1. Call the police and tell them the IMEI of the tracker (it is tied to the SIM card).
      2. Send a command to the tracker SOS# — some models begin to transmit coordinates more often.
      3. Turn on GPS Glaz mode Anxiety (if supported) - this will increase the update frequency to 5 seconds.
      4. Do not try to pursue the hijackers on your own - transfer the data to law enforcement agencies.