Legendary Oka (VAZ-1111) is one of the most compact Soviet cars, which is still in demand due to its maneuverability and efficiency. But before purchasing, repairing, or even regular parking, it is important to know the exact dimensions of the car. For example, Oka width is 1420 mm, and the length is 3200 mm, which makes it ideal for urban environments, but creates restrictions when transporting or installing in a standard-sized garage.

In this article we will not only provide official data from the technical data sheet, but also explain how to correctly measure the dimensions yourself (taking into account mirrors, bumpers and other protruding elements). You will also find out why The width of the Oka with open doors exceeds 2 meters - this is critical when parking in narrow yards or in cramped parking lots. For clarity, we have added a comparison table with other small cars and practical operating tips.

Official dimensions of the VAZ-1111 Oka according to the technical passport

According to factory documentation, basic dimensions Okie (modifications of VAZ-1111, 11113) are as follows:

  • 📏 Length: 3200 mm (3.2 meters) - excluding bumper and towbars.
  • 📐 Width: 1420 mm (1.42 meters) - along the wheel arches, without mirrors.
  • 🔺 Height: 1350 mm (1.35 meters) - to the roof, without antenna or trunk.
  • 🚗 Wheelbase: 2180 mm - the distance between the axles of the front and rear wheels.
  • 🔄 Front/rear track: 1215 mm / 1200 mm - width between the centers of wheels on the same axle.

These parameters are relevant for all modifications, including Oku-011 (with engine from Tavria) and export versions. However, it is important to consider that actual dimensions may differ by 10–30 mm due to body deformations, non-standard bumpers or tuning. For example, after installing body kits or arch extensions width can increase to 1500–1550 mm.

💡

When buying a used Oka, always check the dimensions with a tape measure - unscrupulous sellers may hide the consequences of an accident that distort the geometry of the body.

How to correctly measure the dimensions of the Oka yourself

If you need to know the exact dimensions of your machine (for example, for transport or repair), follow these instructions:

  1. Preparation: Place the car on a level surface, make sure that the tire pressure is normal (1.8–2.0 atm). Use a laser tape measure or a metal ruler at least 2 meters long.
  2. Length: Measure from the outermost point of the front bumper to the outermost point of the rear bumper. If there is a towbar or bulwark, consider them separately.
  3. Width: Measure at the most protruding points - usually the wheel arches or mirrors (if they do not fold). For accuracy, take measurements at the level of the front and rear axles.
  4. Height: From the ground to the highest point of the roof (not including antenna or trunk). If the machine is loaded, the height may decrease by 10–20 mm.

Measure the width with doors open (additional +400 mm on each side)|

Check the symmetry of the body (the difference between the right and left sides should not exceed 5 mm)|

Take into account protruding elements: mirrors, moldings, bumpers|

Take photos of the results for comparison when purchasing spare parts-->

Pay special attention width with doors open - she reaches 2.2–2.3 meters (1420 mm body + ~400 mm for each door). This is critical when parking in a garage or in a narrow parking lot where neighboring cars may interfere with the opening of the doors.

Comparison of Oka's dimensions with other small cars

To understand how compact Oka, compare it with popular analogues:

Model Length, mm Width, mm Height, mm Wheelbase, mm
VAZ-1111 Oka 3200 1420 1350 2180
ZAZ-1102 Tavria 3735 1550 1400 2320
Daewoo Matiz (M100) 3495 1495 1485 2340
Renault Twingo I 3430 1630 1430 2300
Smart Fortwo (W450) 2500 1550 1540 1810

As can be seen from the table, Oka even inferior in length Smart Fortwo, but exceeds it in width. This makes it more stable on the road, but less maneuverable in tight yards. Interestingly, according to the wheelbase Oka closer to Tavriathan European small cars, which affects the smoothness of the ride.

VAZ-1111 Oka|

ZAZ-1102 Tavria|

Daewoo Matiz|

Smart Fortwo|

Other-->

Why is it important to know the dimensions of the Oka: 5 practical reasons

Knowing the exact dimensions of the car will come in handy in the most unexpected situations:

  • 🚪 Parking in the garage: A standard garage is 2.3–2.5 meters wide. If your Oka with open doors it takes 2.2 meters, leaving only 10–30 cm for maneuver. If there is an error in measurements, doors or walls can be damaged.
  • 🚛 Transportation: When transported on a tow truck or in a container, the length of 3.2 meters can become a problem - many platforms are designed for cars from 4 meters. Special fastenings will be required.
  • 🔧 Body repair: For welding or painting, you need to know the exact width of arches and doors. For example, the standard width of the front fender is 500 mm, the rear fender is 480 mm.
  • 🛣️ Traveling to bottlenecks: In some underground parking lots or on mountain roads, the width limit is 1.5 meters. Oka fits with a margin, but with mirrors (width 1600 mm) it may not fit.
  • 💰 Buying covers or awnings: One-size-fits-all cases rarely fit perfectly. For Okie We need models taking into account a short wheelbase (2180 mm) and a narrow gauge.
💡

If you plan to transport the Oka on a tow truck, check in advance the maximum length of the platform - some models do not accept vehicles shorter than 3.5 meters.

Common mistakes when measuring dimensions and how to avoid them

Many owners Okie are faced with inaccurate measurements, which leads to problems during repairs or parking. Here are the typical mistakes:

⚠️ Attention: Never measure the width using the wheel caps - they often protrude beyond the arches by 10-20 mm. Correctly measure along the widest part of the body (usually these are the lines for door stamping).
  • 📉 Ignoring load: A loaded car sags, which reduces ground clearance and height. Always measure dimensions in “combat” conditions - with passengers and luggage.
  • 🔄 Asymmetrical body: After an accident, one side may be wider than the other. Check symmetry by comparing measurements on the right and left.
  • 🚗 Mirrors and antennas: These are often forgotten to be taken into account, although they increase the width to 1600 mm and the height to 1500 mm.
  • 📐 Crooked roulette: Cheap plastic tape measures have an error of up to 5%. For precision, use metal or laser tools.

To avoid errors, use this algorithm:

  1. Take a photo of the car from the front, back and side at right angles.
  2. Place marks on the asphalt (with chalk or tape) at the extreme points of the body.
  3. Measure the distance between the marks with a tape measure.
  4. Repeat the measurements 2-3 times and take the average value.

How Oka's dimensions affect its behavior on the road

Compact dimensions Okie directly related to its controllability and safety:

  • 🔄 Short wheelbase (2180 mm): Makes the car very agile (turning radius - 4.5 meters), but prone to "yaw" at high speeds (over 90 km/h).
  • 🚗 Narrow gauge (1215/1200 mm): Reduces stability in crosswinds or sudden maneuvers. On a wet road Oka can “float” at speeds above 70 km/h.
  • 🛑 Low ground clearance (150 mm): Despite its compact size, the car easily grips the road due to its short overhangs. When loading 4 passengers, the ground clearance decreases to 120 mm.
  • 💨 Aerodynamics: Due to the high body (1350 mm) and short length Oka has a large windage. When overtaking trucks, the drag coefficient (Cx=0.42) plays against the driver.

To improve handling, experienced owners recommend:

  • Install anti-roll bars (especially on the rear axle).
  • Use tires with a low profile (for example, 155/70 R13 instead of the standard 155/80 R13).
  • Avoid overloading - every extra quintal increases roll in corners by 10–15%.
Why does the Oka wobble on the highway?

The short wheelbase and light weight (640 kg) make the car sensitive to road irregularities and side winds. At speeds above 80 km/h, suspension resonance occurs, which increases vibrations. Solution: reduce speed, check wheel alignment and tire pressure (should be the same on all wheels).

Where to find Oka dimensional drawings for repair or tuning

If you need accurate body diagrams (for example, for making parts or planning tuning), look for them in the following sources:

  • 📄 Technical data sheet: The section "Dimensions" provides official data with tolerances.
  • 🔧 Repair manual: Books from the publishing house "Behind the Wheel" or "The Third Rome" contain drawings indicating control points of the body.
  • 🌍 Online catalogs:
    • oka-vaz.ru — a forum with posted diagrams.
    • autocad.ru — 3D models and drawings in DWG format.
    • drive2.ru — owners’ blogs with photos and measurements.
  • 📐 Specialized programs: B AutoCAD or Kompas-3D you can find ready-made models Okie with dimensions.
⚠️ Attention: Be careful with drawings from unverified sources - some “tuning” diagrams contain errors in dimensions (for example, narrowed arches for 175/70 R13 tires, which in practice rub against the body). Always check data against original shop drawings.

For clarity, we present the key control points of the body (in mm):



Front bumper (extreme points): 3200 (length) × 1420 (width)


Rear bumper: 1200 (width between lights)


Roof: 1350 (height) × 1100 (width between pillars)


Doors: 700 (height) × 500 (front width) / 480 (rear)

FAQ: Frequently asked questions about Oka dimensions

Is it possible for a person 190 cm tall to fit into the Oka?

Yes, but with reservations. The cabin height is 1100 mm, and the distance from the pedals to the seat back is 850 mm. A driver who is 190 cm tall will have to move the seat all the way back and bend his knees slightly. The main problem is small gap between head and ceiling (about 5–10 cm). At the same time, the passenger in the rear seat will be even more cramped due to the short wheelbase.

How many containers fit in a standard 20ft container?

A container with a length of 5.9 meters and a width of 2.35 meters can accommodate two Okies, if you place them nose to nose. However, this will require removing the mirrors and bumpers. Without disassembly, only one car will fit with a length reserve (5.9 m vs 3.2 m Okie).

Why does the passport indicate a width of 1420 mm, but in practice the car is wider?

The passport indicates the width of the body (excluding mirrors, moldings and wheel covers). The actual width with open doors is up to 2.2 meters, and with mirrors - up to 1.6 meters. Also, after painting or anti-gravel treatment, the thickness of the paintwork adds 0.5–1 mm to each dimension.

What are the dimensions of the Oka with a trailer?

With standard trailer Oka-1111 (model 8213) total length will be 5.2 meters (3.2 m car + 2 m trailer), and the width will remain 1420 mm (the trailer is 100 mm narrower than the body). Important: the trailer increases the turning radius to 6.5 meters, which is critical in urban conditions.

Is it possible to install 175 mm wide tires on the Oka?

Theoretically yes, but in practice this will cause problems:

  • The 175/70 R13 rear tires will touch the arches when fully loaded.
  • The front wheels may rub against the tie rods when turning.
  • The load on the hub bearings will increase (standard life is 60 thousand km).

Maximum recommended tire width - 165 mm (for example, 165/70 R13).