Self-leveling floor Eunice Next Garage: do-it-yourself professional coating

Installing a quality garage floor is not just a matter of aesthetics, but is critical to the longevity of the space and the owner's comfort. An ordinary concrete floor, even if it is recently poured, over time begins to dust, crack and absorb technical fluids such as oil or gasoline. It is in such conditions that specialized mixtures come to the rescue, including Eunice Next Garage has proven itself as a reliable solution for rooms with high mechanical load.

This material is cement-polymer composite, which after hardening forms a monolithic surface of high strength. Unlike decorative self-leveling floors for living rooms, the composition for garages is developed taking into account extreme operating conditions: temperature changes, impacts with heavy objects and constant movement of car wheels. Understanding the physical and chemical properties of this mixture will allow you to avoid common mistakes during installation.

In this article we will analyze in detail the technical characteristics of the product, consider a step-by-step algorithm for preparing the base and directly applying the composition. The nuances of operation and maintenance will also be touched upon, which will extend the life of your floor for decades. Properly selected technology is a guarantee that you will not have to redo the work in a couple of years.

Technical characteristics and advantages of the composition

Key feature of the mixture Unis Next Garage is its increased wear resistance. The material is able to withstand significant static and dynamic loads, which makes it ideal for parking lots, warehouses and private garages where heavy equipment is stored. The formula is based on special polymers that bind the cement matrix, making it less brittle and more elastic compared to conventional concrete.

An important parameter is chemical resistance. The coating is inert to the effects of fuels and lubricants, road reagents and household chemicals. If oil or antifreeze spills on the floor, you will have enough time to remove the liquid without creating a permanent stain or destroying the structure of the material. This is critical to keeping the premises clean and safe.

Another advantage is non-shrinkage. If the solution preparation technology is followed correctly, the risk of cracking is minimized. The material has good adhesion to mineral substrates, which allows it to be used as a finishing layer or as a high-strength screed for further finishing.

• 🚗 High mechanical strength: Withstands loads from SUV wheels and falling tools.
• 💧 Moisture resistance: the material is not afraid of direct contact with water and can be used in unheated rooms.
• 🛡️ Antistatic: the coating does not accumulate static electricity, which reduces the amount of settling dust.
• ⏱️ Fast hardening: allows you to reduce garage downtime during repair work.

⚠️ Attention: Despite its high strength, the material is not intended for use as a finishing decorative coating without additional protection from ultraviolet radiation, since a slight change in shade (yellowing) is possible under direct sunlight.

Preparing the foundation: a critical stage of work

The success of the entire event depends 80% on the quality of the preparation of the base. Even the most expensive self-leveling floor will peel off if the base is weak, dirty or wet. The first step is to conduct a thorough inspection of the existing screed. All old paintwork, oil stains and bitumen contamination must be completely removed mechanically or chemically.

Cracks and potholes require mandatory repairs. For this purpose, a repair composition similar to the main one is used, or special thixotropic putties. It is important to ensure the solidity of the base: if you hear a dull sound when tapping the screed, it means that there are delaminations that need to be knocked down and repaired. Ignoring this stage will result in the new floor repeating all the defects of the old one.

Particular attention should be paid to the moisture content of the base. Cement-containing mixtures, including Eunice Next Garage, must not be laid on wet concrete. Residual humidity should not exceed 4-5%. If you poured a fresh screed, it must be allowed to dry for 28 days. You can check the humidity with a special device or a simple test with plastic film.

The final preparation step is dust removal and priming. Dust is the main enemy of adhesion. Use a powerful shop vacuum and then apply a deep penetration primer. This will bind residual dust and even out the absorbency of the base, which will prevent the self-leveling floor from drying out too quickly and causing defects.

Preparation of the solution and necessary tools

To work with dry construction mixtures, a specific set of tools is required. You will need a mixing container with a capacity of at least 20 liters, a low-speed drill with a mixing attachment, a needle roller to remove air, a squeegee for leveling and spatulas. Also, do not forget about personal protective equipment: gloves, goggles and a respirator, as cement dust can irritate the respiratory tract.

The process of preparing the solution requires strict adherence to the proportions indicated on the packaging. Typically, 1 kg of mixture requires about 0.2–0.22 liters of water. Exceeding the amount of water is unacceptable, since this drastically reduces the final strength of the coating and can lead to delamination of the material when drying. The water should be clean and at room temperature.

Mixing algorithm:
1. Pour the calculated amount of clean water into the container.
2. Pour the dry mixture into the water (not vice versa!).
3. Mix with a mixer for 2-3 minutes until smooth.
4. Pause for 5 minutes for the solution to mature.
5. Stir again for 1 minute.

The resulting mass should be plastic, homogeneous, without lumps. The viability of the finished solution is about 40-60 minutes, so it is important to calculate your strength and the amount of work. If you are working for the first time, do not knead many bags at once to prevent the mixture from setting in the bucket.

Floor application and leveling technology

Apply Eunice Next Garage should be done at a base and air temperature of +5 to +30 °C. Work begins from the corner opposite the exit, gradually moving towards the door. The solution is poured into strips or puddles and immediately distributed over the surface using a squeegee or spatula, controlling the thickness of the layer.

The optimal layer thickness varies from 10 to 50 mm. If a thicker screed is required, it is better to perform the process in two stages or use special fillers (crushed stone), if the manufacturer’s instructions allow this. It is important to have time to roll the filled surface with a needle roller. This procedure is necessary to remove air bubbles that inevitably form during mixing.

After spreading the mixture and removing air, the surface is left to dry. Drafts and direct sunlight during the drying period are unacceptable, as they cause uneven evaporation of moisture, which leads to cracks. It takes time to gain operational strength: walking on the floor is possible after 24 hours, and full load is allowed after 7-14 days, depending on the thickness of the layer and temperature.

Expansion joints and stress compensation

Any building is subject to thermal expansion and shrinkage. If you pour a monolithic floor with an area of ​​more than 20-30 square meters without expansion joints, the risk of chaotic cracks tends to 100%. Eunice Next Garage, having high strength, still requires proper layout of the floor map.

Expansion joints must coincide with the joints in load-bearing structures and floor slabs. They are also cut or formed when poured in doorways and at the boundaries of columns. The distance between seams in the floor field usually does not exceed 6 meters. These seams are filled with special elastic sealants or profiles that absorb deformations, preventing the coating itself from cracking.

⚠️ Attention: Do not ignore the installation of seams in large rooms. Trying to make a “perfectly flat floor without a single seam” on an area of ​​50 m² is almost guaranteed to result in the floor bursting at its weakest point.

For private garages, the area of which rarely exceeds 20-24 m², an expansion joint around the perimeter is often sufficient. To do this, before pouring, damper tape is glued along the entire perimeter of the walls. It insulates the screed from the walls and compensates for the linear expansion of the material when temperature changes.

Coating care and operational nuances

After complete drying self-leveling floor requires minimal care, but some rules will help preserve its appearance and properties. Regular removal of dust and dirt will prevent the appearance of an abrasive effect, when small grains of sand under the wheels of the car begin to scratch the surface. For washing, you can use water with the addition of neutral detergents.

Avoid prolonged contact of the coating with aggressive acids. Although the material is resistant to fuel and lubricants, it is better to remove acidic electrolyte from the battery or strong solvents immediately. In winter, if the garage is not heated, the coating can easily withstand freeze-thaw cycles, but a sharp temperature change (for example, driving a hot car onto an icy floor) can theoretically create local stress.

In high traffic areas, such as where the car is parked most often, scuff marks may appear over time. This is normal for any material. To restore its protective properties, you can periodically coat the floor with special hardening impregnations (toppings) or waxes for industrial floors.

Common installation errors

Analysis of reviews and reports from builders allows us to identify typical mistakes that beginners make. The first and most common is saving on primer or its complete absence. This leads to the fact that water from the solution quickly goes into the concrete base, and bulk mixture does not have time to gain strength, starting to crumble.

The second mistake is a violation of the temperature regime. Trying to fill the floor in winter in an unheated garage without heating will cause the water in the solution to freeze, ice crystals will destroy the structure, and after thawing the floor will turn into sand. The third mistake is walking on the floor ahead of time or without special shoes, which leaves irreparable defects.

It is also worth mentioning the error with the layer thickness. Pouring too thin a layer (less than 5-10 mm) on an uneven base will lead to rapid abrasion and peeling. If the differences in height are large, you first need to level the floor with cheaper levelers for rough leveling, and Eunice Next Garage use as a final, durable layer.