Owners of vehicles equipped with security systems Starline Tomahawk 9010Often faced with the need for remote heating of the engine in the cold season. The ability to start the power unit without leaving the house significantly saves time and saves the battery life, providing a comfortable temperature in the cabin at the time of landing. Implementation of the function key-start It requires proper pre-configuration and understanding of the logic of the system.
System system Tomahawk 9010 Provides flexible control algorithms that allow the engine to be run by timer, temperature or forced at the user's command. However, if the basic parameters are not programmed correctly, the key fob commands may be ignored or executed with errors. In this article, we will discuss the detailed process of setting up, features of the work tabular and methods of diagnosing malfunctions.
It is important to understand that successful activation depends not only on the serviceability of the remote, but also on the correct connection. signalling ignition and starter circuits. Any interference with the vehicle’s electrical circuits requires compliance with safety measures. Before setting up, make sure that the main key fob has a fresh power supply and is in the zone of confident signal reception.
Programming Auto Start Functions
The first and most important step is to enter the function table programming mode. This is where the parameters are set that determine how it will behave. motor-car When you get a command. To enter, you need to turn off the ignition and press the service button Override (Valet) five times in a row. After the ignition is turned on, the system will emit five audible signals, confirming the entry into the setting mode.
Next, you need to select the desired function using the keychain buttons. Short presses allow you to switch function numbers, and long-term retention of the 3 or 4 button (depending on the firmware version) changes the value of the parameter. Particular attention should be paid to function No. 1, which determines the type of transmission: automatic or mechanical. For gearbox It is required to perform the "software neutralization" procedure before each autorun.
It is also critical to adjust the control of the engine. The system can determine the operating motor by the tachometer, generator or voltage of the onboard network. Incorrect choice of this parameter can lead to the starter spinning to the stop, even when the engine is already started, which is dangerous for the engine. starter and a flywheel.
⚠️ Note: When setting up the type of transmission, be sure to keep in mind that the mechanics require a neutral gear reservation. Ignoring this step can lead to engine start-up in gear and uncontrolled movement of the car.
- 🚗 Function 1: Selection of the type of transmission (ACP or manual transmission) and the algorithm of the power circuits.
- 🌡️ Function 8: Selection of the method of control of the engine operation (tachometer, generator, voltage).
- ⏱️ Function 9: Set starter operating time when you try to start (0.8 to 1.8 sec).
- 🔋 Function 10: Engine type (gasoline/diesel) that affects the delay before starting the starter.
Forced keychain launch
The most common use case is remote launch on the owner’s command. To implement this function on the keychain Tomahawk 9010 There's a keyboard combination. Usually, this is the simultaneous pressing of buttons with the symbols “key” and “open trunk” (or other combinations depending on the specific modification of the remote). If the command is successfully transmitted, the system will flash the headlights and give an audible signal.
The algorithm of the system’s actions when receiving a command is strictly regulated. First, the ignition is turned on, then a pause is waited for pumping fuel or warming up candles (relevant to diesel engines), and only after that it is turned on. starter. If the engine does not start on the first attempt, the system will make two more attempts with an increased scrolling time.
In the process of operation of the engine on command from the keychain, the status is displayed on the display of the remote. You can see if the doors, hood or trunk are open, as when they open, the engine will be locked for safety reasons. Also on the screen displays the time remaining until the automatic stop, if the mode of operation was not set. temperature-wise Or an endless cycle.
If the car does not start from the keychain, check whether the indicator “Check Engine” when the ignition is turned on. If not, it is possible that the system is blocking the start due to a malfunction of the immobilizer or sensors.
There is a nuance with the engine operation time. By default, it is limited to, for example, 10 or 20 minutes. To extend the work without leaving home, you can send a repeat command to extend the time. This is useful if you are lingering, but want the cabin to stay warm.
Start setting by engine temperature
The function of autostart temperature is extremely useful in winter, allowing you to maintain the engine in a warmed-up state without human intervention. To activate this mode, you need to program a threshold temperature at which the system will initiate the start. Tomahawk 9010 It allows you to select several gradations, for example -10 °C, -20 °C or -30 °C.
The temperature sensor in this system is usually built into the main unit or remote, depending on the configuration. It is important to correctly position the sensor if it is external so that its readings are representative. If the sensor is embedded in a unit that is often under the torpedo, it can show the temperature of the cabin rather than the engine, which reduces the efficiency of the function.
When the set temperature is reached, the system will automatically start the engine at the programmed time. After heating up, the engine will stop, and the cycle will repeat the next cooling. This avoids freezing of oil and condensation in the exhaust system.
- ❄️ The threshold of response: selected from the available values (-10, -20, -30 degrees).
- 🕒 Working time: Set separately, usually from 5 to 20 minutes.
- 🔄 Frequency: The system checks the temperature at specific time intervals.
- 🔋 Consumption: Keep in mind that frequent launches increase fuel consumption and wear of the nodes.
⚠️ Note: Do not set a temperature threshold too high (e.g. -5°C) if the car is in a warm garage. This will result in constant false starts and battery discharge.
The effect of temperature on the battery
At low temperatures, the capacity of the lead-acid battery drops to 50-60%. Frequent auto-runs in winter can quickly drain an old battery, so keep an eye out for its condition.
Using a timer for periodic start-up
An alternative to a temperature sensor is to run on a timer. This feature allows the engine to start at fixed intervals: 1, 2, 4 or 24 hours. This mode is convenient if you know the approximate time when the car should be ready for the ride, or if the temperature sensor is faulty.
When the timer is activated, the system counts the time from the moment the mode is turned on. For example, when selecting a 4-hour interval, the first start will occur 4 hours after activation, the second - another 4 hours, and so on. Resetting the timer occurs when the mode is turned off or the battery is discharged.
They usually cannot work at the same time. Priority is given to the function that was activated last, or the one whose condition was fulfilled earlier. In the settings signalling You can set a priority, but most often the system works on the principle of “who first stood up”.
A combination of keychain buttons is used to set the timer. After confirmation, the corresponding icon will appear on the screen (usually a clock or an hourglass). If the icon flashes, then the mode is activated, but the engine has not yet started on the timer. Constant burning indicates that the engine is running on a timer.
Program neutralization procedure for ICP
For owners of cars with manual transmission (ICSW) the implementation of the “software neutralization” procedure is a prerequisite for the operation of the auto-start. This is a safety measure to prevent the engine from starting when the car is in gear. Without this sequence, the command from the keychain will be ignored.
The procedure is performed as follows: stop the car, leave the engine running. Without turning off the ignitions, turn on neutral gear. Then press and hold the 2 button (or a special "key" button) on the key fob until the beep. At this point, the system “remembers” that the car is in neutral gear.
After the signal, you can remove the key from the ignition lock and close the doors. The engine will continue to operate for a while (usually 30 seconds), giving the owner time to get out of the car. After the doors are closed and the delay time expires, the engine will stall and the system will stand on guard with activated readiness for auto-start.
☑️ Checklist of program neutralization
If you forgot to perform this procedure and just turned off the ignition, autostart will not work. Some models Tomahawk allow you to configure automatic neutral execution when turning off the ignition, if the lever is already in a neutral position, but you should not rely on this.
Table of major commands and functions
For ease of setting and use, below is a table with the main commands of the key fob and the corresponding system functions. Knowledge of these combinations will allow you to effectively manage the security complex without reference to the instructions every time.
| Action. | Button combination | The result |
|---|---|---|
| Put security on. | Button 1 (short) | Locking doors, activating sensors |
| Turn off security. | Button 2 (short) | Opening doors, deactivating mode |
| Auto-start of the engine | Button 1 + Button 2 (long) | Starting the engine off the keychain |
| Stopping the engine | Button 1 + Button 2 (long) | Smoking of the running engine |
| Opening the trunk | Button 3 (long) | Unlocking the trunk lock |
Please note that the length of the pressing is important. Short pressing (less than 0.5 seconds) and long pressing (more than 1 second) often perform different functions or serve to change the values of parameters. In some firmware versions, the combinations may differ, so always check with the manual of your particular model.
Also, the table does not specify the functions of car search and silent security, which are also available to the user. To search for a car, a double short press on the security button is usually used, which causes a short-term siren signal and a flash of dimensions.
Diagnostics and problem-solving
If the auto start stopped working, the first thing you need to check the condition of the car. An open hood, trunk or door, as well as an untightened hand brake, block the start. The keychain usually displays the corresponding indicator. Also a common cause is a discharged battery of the car, the voltage of which fell below the permissible threshold.
Another common problem is the loss of communication between the key fob and the main unit. If you press the buttons, the car reacts (blinks), but the command to start does not pass, perhaps the settings of the communication channel have gone wrong. In this case, a procedure is required.