Direct failure of the washing machine Samsung from transition to spin mode is most often associated with drum locking due to uneven distribution of linen or critical excess of the permissible loading weight. The electronic control module detects an abnormal load on the engine and forcibly stops the cycle to prevent mechanical destruction of the bearing assembly or breakage of the drive belt. In some cases, the diagnostic system mistakenly interprets the data from the water level sensor, believing that the liquid has not been completely drained, which also makes the high-speed rotation procedure physically impossible and dangerous for the design.
If you observe that Samsung washing machine does not pushFirst of all, you should check the error code displayed on the digital display, or pay attention to the flashing of indicators if the screen is missing. Modern models of the brand are equipped with a developed self-diagnostic system, which can indicate a specific node: whether it is a self-diagnostic. 5E (spill problem) UE (imbalance) or 3E (engine malfunction). Ignoring these signals and attempting to restart the program without addressing the root cause can lead to an aggravation of the breakdown and the failure of expensive electronic components.
Blockage due to imbalance and overload
The most common reason for which Samsung refuses to perform spinning, is a banal imbalance of the underwear in the drum. When washed items are put together in one dense lump on one side, the centrifugal force when attempting to disperse causes a strong vibration that sensors perceive as an emergency. In this case, motor The program may try to fluff the underwear several times, slowly rotating the drum in different directions, but if the balance is not restored, the cycle ends without pressing.
Overloading also plays a critical role: if you load more dry linen than the passport capacity model allows, wet fabrics swell and become excessively heavy. The engine simply cannot develop the necessary revolutions for high-quality spin, and the protection system blocks this stage of washing.
⚠️ Attention: Constant washing with overload or severe imbalance leads to rapid wear of shock absorbers and suspension springs, and can also cause cracks in the tank.
To eliminate the problem, you need to open the hatch, manually straighten the sticky things and distribute them evenly over the inner diameter of the drum. If there are too many things, some of them should be taken out and an additional cycle started. In some models, the function Auto Balance The system tries to do this automatically, but if there is a strong distortion, the user intervention is necessary.
Water drain problems and blockages
If there is water in the tank, the washing machine Samsung physically unable to start the spin, as this will lead to hydraulic shock and damage to the mechanism. The main suspect here is a clogged drain filter located in the bottom of the case behind the decorative panel. Pile, threads, coins and other small items accumulate over time in the filter element, preventing the free passage of water to the pump.
In addition to mechanical damage, the problem can be found in the drain-pump. The impeller pump could wind the threads that would block its rotation, or burned the winding of the electric motor pump. In the first case, the machine will buzz, but not pump water, in the second - emit a characteristic click or be silent. It is also worth checking the corrugated hose running from tank to pump for large items stuck there, such as buttons or bra bones.
☑️ Diagnostics of the drain system
Often users forget to check the sewer pipe or siphon to which the drain hose is connected. If a blockage formed in the general sewerage system of the apartment, water will not leave the car, regardless of the state of its internal filters. Visual inspection of the place of connection of the hose and attempt to drain into a separate container will help to localize the problem: if the bucket water goes quickly, and the sewer - no, then the problem in the communications at home.
| Error code | Description of the problem | Probable cause | User actions |
|---|---|---|---|
| 5E / SE | The water doesn't drain. | Filter or hose clog | Clean the filter, check the hose. |
| UE / UB | Laundry imbalance | Things are lost in a coma | Hand-stretching laundry |
| 3E / 3E1 | Engine malfunction | Trouble with the tachodist | Master's call, brush check. |
| HE | Heating error | Faulty TEN or sensor | Check the heating element |
Failure of the heating element (TEN)
Paradoxically, the lack of spin in washing machines Samsung Often caused by a faulty heating element, even if the program is selected without heating (e.g., "Cold Washing"). The fact is that many models are programmed to check the performance of the TEN at the beginning of the cycle. If the control module detects a circuit break or a short circuit in the heater, it can interrupt the program until the spin stage to avoid damage to the electronics.
In addition, if the heater is covered with a thick layer of scale, it can overheat and go into defense, or vice versa, do not have time to heat the water to a given temperature in the allotted time. Some washing algorithms require a certain temperature to be reached before switching to rinsing and spinning. If the water stays cold, the machine will heat it indefinitely or give an error, without starting to rotate the drum at high revs.
How to check the TEN multimeter
For diagnosis, it is necessary to remove the back cover, disconnect the wires from the TEN contacts and switch the multimeter to the resistance measurement mode (Oma). The normal resistance of a serviceable heater with a power of 1700-1900 W is approximately 25-35 Ohms. If the device shows a one (break) or a zero (short circuit), the element needs to be replaced. It is also important to check the breakdown on the body, touching one contact probe, and the other - the metal housing of the TEN; the device should be silent.
Replacing a TEN is not the most difficult procedure, but it requires accuracy. It is necessary to drain the remains of water, dismantle the old element, clean the landing place from scale and install a new one, tightening the clamping nut. The use of original spare parts or quality analogues guarantees a long service life and proper operation of the thermoregulation system.
Wear of brushes and engine malfunctions
Electric motor in washing machines Samsung The collector type is equipped with graphite brushes that transmit current to the rotor. Over time, they wear off and contact becomes unstable or disappears completely. If the brush length becomes less than the critical norm, the engine stops developing the necessary revolutions for spinning, although it can continue to spin the drum at low speeds for washing.
The second important element is the tachodatnik - a small detail fixed to the engine body, which reads the speed of rotation of the shaft. If the tachodilator flew off, oxidized or failed, the control module does not receive correct speed data and blocks the spin mode. The machine may attempt to disperse the drum, but, seeing no reaction, stops the attempt and proceeds to the completion of the program.
⚠️ Attention: Attempts to operate a machine with worn brushes can lead to burnout of the engine manifold, which will make its repair economically inexpedient.
Diagnostics of the engine requires partial disassembly of the unit. It is necessary to remove the belt, disconnect the wires and possibly dismantle the motor itself for visual inspection of the brushes. Their length shall be at least 1 cm. It is also worth checking the condition of collector slats for the presence of soda and chips. Cleaning the manifold and replacing the brushes often give the machine a second life without having to buy a new motor.
When replacing brushes, be sure to wipe them by scrolling the engine manually or in test mode several times so that they take the shape of a collector.
Failures in the electronic module
Washing machine Samsung It is controlled by a complex electronic module that can be subject to failures due to voltage surges in the network or moisture. If the control board burned simistors controlling the engine or pump, or damaged tracks, the machine will cease to execute commands to press. Sometimes the problem lies in the oxidation of the contacts of the connectors connecting the module with the actuators.
A software failure can also be a reason for a stoppage. In this case, a complete reset or system reboot helps. To do this, the machine is disconnected from the power grid for 15-20 minutes, and then turned on again. If the problem was caused by a temporary sensor erroneous signal, the cycle can be successful after the reboot.
However, if the situation recurs after the reboot and the diagnosis shows errors related to engine control (see below).3E, 3E1, 3E2) the control module may need to be repaired or replaced. Independent repair of the board is possible only if you have skills in working with a soldering iron and electronics, in other cases it is better to contact a service center.
Error resetting often solves the problem of a one-time software failure, but does not eliminate physical faults in parts.
Mechanical damage and wear of nodes
The mechanical causes of failure of pressing can be attributed to stretching or weakening of the drive belt. If the belt jumped off the pulley or stretched too much, it will slip, not transferring enough force from the engine to the drum. Visually, this can be seen by opening the back cover of the car: the belt should be stretched and sit in the grooves of the pulleys.
It is also worth mentioning the wear of the tank unit bearings. If the machine makes a strong hum, similar to the roar of an airplane, and then stops, perhaps the bearings are jammed. Operation in this mode is dangerous: the shaft can turn around, damaging the omentum and running water on electronic components, which will lead to a short circuit.
The destruction of the cross drum is another serious mechanical malfunction. This is a metal part to which the back wall of the drum is attached. Under the influence of aggressive detergents and moisture, it can corrode and burst. As a result, the drum is swayed and the machine blocks the spin to avoid the final destruction of the tank. Replacing the cross is a time-consuming process that requires complete disassembly of the machine and often replacement of the tank itself in the assembly.
Frequently Asked Questions (FAQ)
Why does Samsung only push at low speeds?
This may be due to activation of the "No folds" or "Delicate washing" mode, where high speeds are not provided. Also, the reason may lie in the wear of the engine brushes, which cannot gain full speed, or in a software error of the control module.
What if the 5E code is on and the machine is not pressing?
The 5E code indicates a water drain problem. It is necessary to check and clean the drain filter, make sure that the drain hose is not clamped or raised too high, and check the sewer pipe for clogs.
Can I hand-wring clothes if the car breaks down?
Yes, many models. Samsung have the function "Plum" or "Push" in the menu of additional options. You can try to start a separate cycle of spinning. If the electronics are blocked, you will have to drain the water through the filter and remove the laundry manually.
How to Reset a Mistake on a Samsung Washing Machine?
To reset the error, disconnect the car from the socket for 15-20 minutes. In some models, it helps to simultaneously press the Temperature and Press buttons (or other combinations depending on the model) for 5 seconds, but full shutdown is a universal method.
Why does the machine still not push back after replacing the TEN?
It is possible that the new TENG is faulty, incorrectly installed (no contact), or the problem was not the heater. The fuse on the control module could also burn or an error in the memory of the processor after replacing the part is required.