Autostart on Sherkhan Logicar: detailed installation and configuration guide

Alarm Sherkhan Logicar has long gained popularity among car owners due to its reliability and wide functionality. One of the most popular functions remains auto engine start — the ability to remotely start the car to warm up the interior in winter or cool it in summer. However, setting up this option often raises questions: how to connect the module correctly, what parameters to set in the menu, and why does the system sometimes refuse to work?

In this article we will analyze all the nuances of autorun on Sherkhan Logikar — from choosing equipment to diagnosing common errors. You will find out what additional relays may be required for correct operation, how to set timers and temperature settings, and also what to do if the engine stalls immediately after starting. We will pay special attention compatibility with different car brands (from VAZ up to Toyota) and legal aspects of using autostart in 2026.

If you are just planning to purchase an alarm system or have already encountered operational problems, you will find answers to most questions here. And for those who prefer visual instructions, we provide connection diagrams and video guides from official dealers.

1. Which Sherkhan Logicar configurations support autostart?

Not all versions Sherkhan Logicar equipped with an autostart function. To avoid disappointment, check the labeling on the box or paperwork. Main modifications that support remote start:

• 🔹 Logicar 3 - basic version without autostart (security functions only).
• 🔹 Logicar 5 - supports autorun, but requires an additional module CAN-LIN for most foreign cars.
• 🔹 Logicar 7/9 — full support for autorun with flexible settings (timers, temperature, start by alarm).
• 🔹 Logicar 10 - flagship model with automatic detection of gearbox type (automatic/manual transmission) and integration with a mobile application.

Important: even if your version supports autostart, for some cars (for example, Hyundai/Kia with the system Smart Key) will be required immobilizer crawler. Without it, the engine will stall 3-5 seconds after starting.

How to check compatibility? Go to Sherkhan official website and use the selection service by car make. The alternative is to study user manual (section "List of supported vehicles").

2. Autostart connection diagrams: step-by-step instructions

Installing autorun on Sherkhan Logikar requires intervention in the vehicle's electrical wiring. If you are not confident in your skills, it is better to turn to professionals. Below we present universal scheme for most cars with manual and automatic transmission.

Main connection steps:

1. Connection main block to nutrition (+12V and mass).
2. Connection to ignition, starter and generator.
3. Installation door limit switches and shock sensor.
4. Integration with CAN bus (for foreign cars).
5. Settings immobilizer crawler (if required).

For clarity, here is a table with wire colors (relevant for Logicar 7/9):

⚠️ Attention: On vehicles with automatic transmission be sure to connect the wire Neutral Safety (gray) to the neutral sensor! Otherwise, autorun will be blocked.

Download the wiring diagram for your car model|

Purchase additional relays (4-pin, 12V)|

Prepare tools: multimeter, soldering iron, electrical tape |

Disconnect the battery before starting work|

Mark all wires with markers for convenience -->

3. Configuring autostart parameters in the alarm menu

After connecting, you need to configure the autostart parameters through the alarm menu. To do this:

1. Start the car with the key.
2. Click the button Valet 3 times in a row - you will get into service menu.
3. Select section Autostart (buttons ▲/▼).
4. Configure the following settings:
   • 🕒 Start timer (interval: 1–24 hours).
   • 🌡️ Temperature (eg starting at −10°C).
   • 🔄 Number of attempts (we recommend 2-3).
   • ⏱️ Starter cranking time (usually 0.8–1.2 sec).

For vehicles with Automatic transmission be sure to activate the option Automatic in the settings! Otherwise, the system will require you to press the clutch pedal (which is not there).

⚠️ Attention: If the engine stalls immediately after starting, check the setting Time Ignition (ignition hold time). For most machines, the optimal value is 15–20 seconds.

4. Typical errors and their elimination

Even with proper installation, autorun may not work properly. Let's look at the most common problems and ways to solve them:

• 🔋 The engine does not start with the key fob:
  • Check the battery charge (voltage should be ≥ 12.4V).
  • Make sure the car is parked neutral gear (for manual transmission) or in mode P (for automatic transmission).
  • Check the wire connection Handbrake — the alarm blocks the start if the parking brake does not lock.
• 🔄 The engine starts and immediately stalls:
  • Most likely not connected immobilizer crawler.
  • Check the setting Time Ignition — if the value is too small, the engine does not have time to “catch” the speed.
  • On foreign cars with CAN bus Module firmware may need to be updated.
• ❄️ Autostart does not work based on temperature:
  • Check the connection of the temperature sensor (usually included).
  • Make sure that the option in the menu is activated Temp Start.
  • On some versions Logicar 5 The temperature sensor only works with the additional module.

If the problem is not solved, try resetting the alarm settings to factory settings (press and hold Valet for 10 seconds) and repeat the setting.

5. Legal nuances of using autostart in 2026

Many car owners ask: Is autostart allowed by law? There is no direct ban on this function in Russia, but there are several important points:

• 📜 Traffic rules and autostart:

  According to clause 2.5 of the traffic rules, the driver is obliged to ensure that the car is in good condition. If autorun leads to uncontrolled movement of the machine (for example, on a slope without a handbrake), this may be considered a violation.

• 🚨 Fines for running the engine:

  In some regions (for example, Moscow, St. Petersburg) there are rules prohibiting warming up the car while parked for more than 5 minutes. Fine - up to 1 500 ₽ (Article 8.23 of the Code of Administrative Offenses of the Russian Federation).

• 🔐 Insurance and auto start:

  If a car is stolen with a working autostart, the insurance company may refuse to pay, citing failure to ensure the safety of the vehicle (Clause 1 of Article 964 of the Civil Code of the Russian Federation).

⚠️ Attention: During the winter period (from November to March), in most regions there are relaxations for autostart, but only if two conditions are met:

1. The car is within the owner's visibility range.
2. The engine runs no more 10 minutes.

To avoid problems, use autorun only in guarded parking lots or in the garage. We also recommend installing an additional motion sensor, which will turn off the engine if the car starts to move without the key.

6. Compatible with popular car brands

Autorun function on Sherkhan Logikar Doesn't work equally well on all machines. Below is a table of compatibility with popular brands and possible pitfalls:

For accurate information on your model, use official compatibility catalog or consult your installer.

7. Alternative ways to control autorun

In addition to the standard key fob, Sherkhan Logikar supports several alternative ways to control autorun:

• 📱 Mobile application Sherkhan Mobile:

  Available for Android and iOS. Allows you to start the engine from your phone, but requires installation GSM module (optional). The range is unlimited (if there is Internet access).

• 🔑 Tag trigger (RFID):

  On some versions (Logicar 10) you can link an RFID tag to an alarm. We brought the tag to the reader and the engine started.

• ⏰ Auto start on alarm clock:

  The function is available in the menu Timer Settings. You can program it to start, for example, every weekday at 7:00.

• 🌡️ Trigger based on interior temperature:

  Requires additional sensor (included) Logicar 9/10). The engine will start if the temperature drops below the set value.

1. Turn off the ignition.
2. Press and hold Valet 15 seconds.
3. Wait for 5 beeps - the settings will be reset.