Washing machine Samsung stops gaining momentum of the drum immediately before or immediately after the drain, which is often accompanied by a characteristic humming of the engine or a complete stop of the cycle. This behavior indicates that the automation has not received a signal of readiness for the spin stage, or the actuator cannot physically develop the necessary turns due to blocking or breakage of the node. In most cases, the self-diagnosis system has already detected the failure and displayed the corresponding error code, which is the key to understanding the nature of the malfunction. Ignoring these signals and attempting to restart the program without addressing the root cause can cause the engine to overheat or the control module to fail.
The primary task of the owner is to determine whether the problem is software related to the imbalance of the linen, or technical, requiring disassembly of the unit. Modern models Smart Check They are able to independently determine the level of vibration and load distribution, forcibly stopping the spin at the risk of damage to the bearings or tank. If the machine is gaining water, washing, but the water does not drain and does not go to press, then the malfunction lies in the drainage system or level sensors. Understanding the algorithm of the device allows you to quickly localize the node that requires intervention.
Decoding error codes and primary diagnosis
When the washing machine Samsung does not go into spin mode, it most often signals this digital combination on the display. Codes 5E or SE indicate problems with water drainage: the machine cannot pump out the liquid, so the transition to a high-speed mode is blocked programmatically. Mistakes. UE or U6 evidence of a strong imbalance of linen, when things are lost in a coma on one side of the drum, and the electronics can not evenly distribute the load for safe rotation.
More complex engine or control module malfunctions are displayed by codes 3E, 3E1, 3E2, 3E3 or 3E4. These values indicate that the tachodilator does not fix the rotation of the motor, or the engine itself cannot start. If it's on the screen AEThis means a communication error between the main module and the control panel, which can also block the execution of commands. For accurate diagnosis, it is useful to know what these signals mean:
- 🔍 5E/SE - water does not go away, check the filter and pump.
- ⚖️ UE/U6 - load imbalance, requires redistribution of things.
- ⚡ 3E/3E1-3E4 Failure of the engine, brushes or control module.
- 📡 AE - violation of communication between electronic boards.
⚠️ Attention: If the error code flashes or disappears after the machine is turned off, it does not mean that the problem is solved. Electronics could go into emergency mode, and a restart without repair could (burn) the simistors on the control board.
Drain system problems as a reason for stopping
The most common reason why Samsung doesn’t start spinning, it’s a banal inability to pump water out of the tank. The algorithm of the machine is built so that the water level sensor (pressostat) must fix the “dry” tank before starting high revs. If the water is in the tank even at a minimum level, the controller blocks the command to press to avoid hydraulic shock and water splashing through the hatch cuff.
The first thing you need to check the drain filter located in the lower right part of the case behind the decorative panel. Clogging the filter with pile, coins or buttons creates resistance that the pump cannot cope with. It is also worth examining the corrugated hose going from the tank to the pump, and the pipe itself, going into the sewer. Often users forget that the height of the drain hose should not exceed 80-100 cm, otherwise the pump power will not be enough to lift the water column.
If there are no mechanical obstacles, but the pump buzzing is absent or the sound changes to intermittent, it may have failed itself. drain-pump. The wing could have turned on the shaft or the pump engine winding burned. In some cases (a foreign object) jams the impeller and the engine shaft cannot turn, causing the humming and heating of the unit.
☑️ Diagnostics of the drain system
Laundry imbalance and drum overload
Modern washing machines Samsung is equipped with a sensitive vibration control system. If during washing the linen (especially large, like blankets or jackets) is lost in one dense lump, the centrifugal force when trying to disperse causes a strong drumbeat. Sensors capture the critical amplitude of the oscillation of the body and forcibly stop the program to prevent the destruction of bearings or the impact of the tank against the wall of the case.
Often users mistakenly believe that the more things loaded, the more efficient the washing. However, for high-quality pressing, free space inside the drum is necessary so that things can be straightened out under the action of centrifugal force. Overloading Weight is also dangerous: the engine works at the limit of possibilities, the belt (if any) slips, and the inverter motor goes into protection by current.
To eliminate the imbalance error, it is necessary to:
- 👕 Stop the program and open the hatch (if the lock allows).
- 👐 Hand-spread the lost linen and evenly distribute it in a circle.
- 📉 Reduce the number of items if the load exceeds the recommended volume (usually 2/3 of the reel).
- 🔄 Start the "Push + Plum" mode to check the work.
⚠️ Attention: Do not try to force the drum to disperse with imbalance by holding the door or pressing buttons. This can lead to breakage of shock absorbers or failure of the counterweight.
Failure of the engine and brush assembly
If the water is drained, the laundry is distributed evenly, but the machine is buzzing and does not turn the drum, the problem lies in the drive. In the models with collector The most common cause of wear is graphite brushes. Over time, they wear off, contact with the manifold deteriorates, and the motor loses the power necessary to reach high spin speeds (usually 800-1200 rpm).
When wearing brushes, the machine can wash normally (low revs), but at the spin stage the engine only hums or twitches. In direct-drive models (Direct Drive) no brushes, but may fail Hall sensors or the stator itself. Diagnostics of the collector motor requires removal of the back cover (or the front, depending on the model) and visual inspection of the length of the brushes. If the length is less than 1.5 cm, replacement is necessary.
It is also worth checking the condition. drive-belt. If it is stretched, it will slip on the engine pulley when trying to overclock. The tension must be such that the belt bends by about 1.5 cm when pressed with a finger. Weakening of the pulley bolt or wear of the pulley itself also leads to loss of torque transmission.
How to check engine brushes
The engine must be removed for inspection. The brushes are located on the sides of the collector in special holders. Remove them and measure the length of the working part. If the graphite has worn to metal or the spring does not press the brush tightly, the motor will work unstable. Also inspect the collector for the presence of sodium - it can be cleaned with alcohol and fine sandpaper, but deep furrows require a replacement of the motor.
Failure of the control module and sensors
Electronic control (fee) is the washing machine's "brain" Samsung. If it receives incorrect data from sensors or has defects itself, it will not give a command to spin. A common cause of false readings is a malfunction of the pressostat (water level sensor). Even if there is no water in the tank, the stuck contacts of the pressostat can “tell” the module that the tank is full, and the program will wait for the drain indefinitely.
The tube running from the tank to the pressostat should also be checked. If a water plug has formed in it or it is clogged with dirt, the air pressure is not transmitted to the membrane of the sensor. The machine does not see that the water has gone. Another critical element. TAEN (heater) In many models, the algorithm prohibits spinning if the TEN has not warmed up to a certain temperature or, conversely, is pierced on the body, which causes a current leak and the protection is triggered.
Diagnostics of the control module at home is limited to visual inspection for burnt tracks, swollen capacitors or traces of moisture. Often the problem lies in the “dump” of contacts or microcracks of soldering due to vibration.
Technical parameters and fault table
To systematize possible reasons why Samsung does not come out on the spin, it is convenient to use a summary table. It will help to compare the symptoms with the likely nodes of breakdown. It is important to understand that the same symptom (for example, humming) can be caused by different causes, so the test should be comprehensive.
| Symptoms. | Probable cause | Error code (example) | Difficulty of repair |
|---|---|---|---|
| Water in the tank, pump buzzing | Filter/pump clog | 5E, SE | Low. |
| The drum's standing, there's no water. | Wear of engine brushes | 3E, 3E1 | Medium |
| Vibration, knocking. | Laundry imbalance | UE, U6 | Low. |
| The car is humming, but it's not spinning. | Bearing jamming | Absent. | Tall. |
| No reaction from teams | Control module failure | Different | Tall. |
Useful tip: Before calling the wizard, try running the Plum mode separately. If the water drains normally, but there is no pressing - the problem is more in the engine or module. If the water does not go away, the problem is in the pump or filter.
Prevention and operational rules
To avoid situations where the washing machine Samsung stops pushing, it is important to follow the rules of operation. Regular cleaning of the drain filter (every 1-2 months) will prevent 80% of drain problems. The use of special scale products for the heater and drum will prolong the life of the heating element and sensors, which indirectly affect the washing cycles.
Watch the weight of the laundry loaded. The maximum loading specified in the passport (e.g. 5 kg or 7 kg) refers to dry items. Wet underwear is heavier, and the engine may not cope with a sharp set of turns if the drum is crammed to the tie. It is also recommended to use wash bags for small items so that they do not fall into the gap between the drum and the tank, blocking the rotation.
⚠️ Attention: Never leave water in the tank after washing for a long time. This leads to souring of bearings and corrosion of metal elements, which will eventually cause the drum to leak and jam.
In 70% of cases, the problem of “no pressing” is solved by cleaning the filter or laying out the laundry. If simple methods do not help, a diagnostic of the engine and electronics is required.
Why is the car humming, but the drum doesn't spin when pressed?
The buzz indicates that the engine is getting voltage, but can not turn the shaft. Causes: jamming of the drum bearing, wear of the brushes of the collector motor, slipping of the belt or getting stuck in a foreign object between the tank and the drum.
Can I start the spin manually if the car is up?
Forced to start the pressing can be by selecting the program "Plum + Press". However, if the reason for the stoppage is not fixed (e.g., the pump is not working), the machine will stand again at the same stage or will issue an error. This does not solve the problem, but only confirms the presence of a malfunction.
What to do if the 3E code is on fire?
The 3E code indicates a problem with the engine. You need to check the brushes (if the motor is a collector), the contacts of the wiring going to the motor, and the tachodaktik. If the brushes are intact, the engine itself or the simistor on the control board may be faulty.
Does the hardness of the water affect the possibility of spinning?
Directly, no. However, hard water causes the formation of scale on the TENS, which can lead to its overheating and breakdown on the body. In some models, this causes failures in the operation of the control module, which can block the cycle, considering the situation to be an emergency.