Indesit washing machine does not spin clothes: reasons and what to do

Washing machine Indesit stopped spinning the laundry, but you don’t know what’s wrong? This problem occurs in models WISL 85, IWSC 5105, WITL 86 and other series of the brand. In 80% of cases the malfunction is related to clogged drain system, pump breakdown or incorrect program settings. But sometimes more serious details are to blame - e.g. tachometer or electronic module.

In this article we will look at all possible reasonswhy the machine Indesit does not press, and we will also give step by step instructions for self-diagnosis and repair. You will learn how to check the drain filter, ring the engine with a tester, and even reset errors on the control panel - without calling a technician. And if the problem turns out to be more complex, we will tell you how much the repair at the service center will cost.

⚠️ Important: If the machine Indesit not only does it not wring out, but also does not drain water, go straight to the section about clogs and the pump. If the water is drained, but the drum does not spin at high speeds, read about drive belt or electronics.

1. Blockage in the drain system is the most common cause.

If the washing machine Indesit does not wring out laundry, but at the same time water remains in the drum after washing - the problem is almost certainly a clog. The drainage system consists of three key elements: drain filter, pipe and pump (pump). Any one of them can become clogged.

As a rule, blockages are formed due to:

• 🧦 Hair, threads and lint from clothes (especially after washing woolen items or carpets).
• 🍃 Garbage from pockets (coins, papers, buttons).
• 🧴 Residues of powder or conditioner, which over time turn into a thick raid.
• 🦠 Fungus or mold (if the machine has been idle for a long time with water inside).

First check drain filter — it is located at the bottom of the front panel under a small cover. On models Indesit WISL 85 and IWSC 5105 the filter is usually on the right, on WITL 86 - left. How to clean it:

Disconnect the machine from the mains and turn off the water|Substitute a water container (~0.5 liters will flow when you open the filter)|Turn the filter handle counterclockwise and pull it out|Remove debris and rinse under running water|Check the hole in the machine for foreign objects-->

If after cleaning the filter the water still does not drain, the problem may be nozzle (the hose connecting the tank and the pump) or the pump. To check them, you need to remove the back or front panel of the machine (depending on the model). Hair and threads often accumulate in the nozzle, and the pump can jam due to debris.

⚠️ Attention: If, when trying to drain the machine Indesit publishes buzzing sound, but the water does not go away - this is a sign stuck pump. Do not try to turn on the spin again: this may burn the pump motor winding.

2. Malfunction of the drain pump (pump)

A drain pump is a small electric motor with an impeller that pumps water out of the tank. If it's broken, the machine Indesit can't drain the water and, accordingly, will not go to spin. Signs of a pump malfunction:

• 🔊 The machine hums, but the water does not drain.
• 💧 An error appears on the display F05 or F11 (code depends on model).
• 🔌 After turning on the spin cycle, the protection is triggered and the machine turns off.

To test the pump, follow these steps:

1. Unplug the machine and drain the water through the emergency hose (usually located next to the filter).
2. Remove the back or front panel (on models Indesit WISL usually the back IWSC - front).
3. Find the pump - it looks like a plastic cylinder with wires and pipes.
4. Disconnect the wires and check the winding resistance with a tester (should be ~150–200 Ohms). If the device shows 0 or ∞ - the pump is faulty.

If the pump does not work, it needs to be replaced. Cost of a new pump for Indesit - from 1,200 to 2,500 rubles (depending on model). Replacement at a service center will cost 1,500–3,000 rubles taking into account work.

3. Problems with the drive belt

If the washing machine Indesit drains water, but the drum does not rotate during the spin cycle (or rotates very slowly), the problem may be drive belt. This belt transmits rotation from the engine to the drum. Over time, it stretches, cracks, or falls off the pulley.

How to check the belt:

• 🔧 Remove the back cover of the machine (after unplugging it from the network!).
• 👀 Inspect the belt: if it torn, stretched or slipped, it needs to be replaced.
• 🔄 Check the tension: a normal belt should bend no more than 10–15 mm when pressed with a finger.

If the belt is intact but slips, it can be tightened by adjusting the position of the engine. However, in most cases, it is better to replace a stretched belt. The cost of a new one is from 500 to 1,500 rubles, depending on model Indesit.

⚠️ Attention: On some models (for example, Indesit WITL 106) the belt may fall off due to worn drum pulley. If the problem persists after replacing the belt, check the pulley for cracks or chips.

4. Failure of the tachometer (speed sensor)

A tachometer is a small sensor that controls the rotation speed of the drum. If it fails, the washing machine Indesit can:

• ⚡ Do not go into spin mode.
• 🌀 Rotate the drum jerkily or at too low speeds.
• 🚨 Give an error F02 or F08 (on models with display).

The sensor is located on the engine housing. To check it:

1. Remove the back cover of the machine.
2. Find the tachometer - it looks like a small box of wires attached to the engine.
3. Disconnect the connector and check the resistance with a multimeter (should be within 50–150 Ohm).
4. If there are no readings or are very different, the sensor is faulty.

The cost of a new tachometer for Indesit — 600–1,200 rubles. Replacement takes 15–20 minutes and does not require special skills.

How to temporarily bypass a faulty tachometer?

If the sensor is broken and you need to wash it urgently, you can try to start the spin cycle manually:

1. Select the "Drain" program and wait until the water drains.

2. Switch the machine to the “Spin” mode (if there is a separate button).

3. Manually rotate the drum - sometimes this helps the mechanism work.

⚠️ This is a temporary solution! Prolonged operation without a sensor can lead to engine damage.

5. Motor or electronic module malfunction

If all previous reasons are excluded, but the washing machine Indesit still does not press, the problem may lie in engine or control module (board). These are the most serious breakdowns, and their repair usually requires the intervention of a specialist.

Signs of engine trouble:

• 🔥 The machine knocks out the machine when switching to spin mode.
• 🛑 The drum does not rotate in any mode.
• 💨 It smells like burning (burnt winding insulation).

To check the engine:

1. Remove the rear cover and locate the engine (usually down under the tank).
2. Disconnect the wires and check the windings with a tester:
   • The resistance between the terminals should be ~20–50 Ohm.
   • Resistance between terminal and body - ∞ (if there is contact, the engine is “broken”).

If the motor is faulty, it can be repaired (rewind the windings) or replaced. New motor for Indesit worth it 4,000–8,000 rubles, depending on power.

Symptoms of a control module malfunction:

• 📛 The machine turns on, but does not respond to the buttons.
• 🔄 Switches programs independently.
• 🚨 Gives random errors (for example, F18 or F20).

The control module is the “brain” of the washing machine. Its repair or replacement will cost 3,000–6,000 rubles. In some cases it helps factory reset:

1. Unplug the machine for 10 minutes.
2. Turn on and hold the Start/Pause button for 5-10 seconds.
3. Select the "Cotton 60°" program and start without laundry.

6. Incorrect settings or drum overload

Sometimes the reason for the lack of spinning lies not in a breakdown, but in improper use. Here are the most common user mistakes:

• 🧺 Drum overload - if there is too much laundry, the machine will not be able to distribute it evenly for spinning. Maximum load for most models Indesit — 5–7 kg (see instructions!).
• 🌀 Wrong washing mode — some programs (for example, “Wool” or “Delicate Wash”) turn off the spin cycle automatically.
• 🔄 Disabled spin in settings — some models have the “No spin” option (indicated by the 🚫🌀 icon).
• 🧼 Too much powder - excess detergent leads to excessive foaming, and the machine does not spin.

To fix the problem:

1. Check the weight of the laundry - if there is too much, remove some items.
2. Select a spin program (e.g. Cotton or Synthetic).
3. Make sure that the No Spin indicator on the panel is not lit.
4. If there is too much foam, run an additional rinse.

⚠️ Attention: If the machine Indesit does not spin up only at high speeds (for example, at 1000–1200 rpm), but works at 400–600, the problem may be worn bearings. In this case, a strong hum or grinding noise will be heard during the spin cycle.

7. Wear of bearings and oil seal

Bearings and oil seal ensure smooth rotation of the drum. Over time, they wear out, and the machine begins to:

• 🔊 Make a lot of noise during the spin cycle (like a jet plane).
• 🌀 Vibrate and “jump” even on a flat surface.
• 💧 Leak (if the seal is damaged).

You can check the bearings like this:

1. Turn the drum by hand - if you hear crunching, grinding or play, bearings are worn out.
2. Rock the drum up and down: if it “walks” more than 1–2 mm, replacement is required.

Bearing repair is one of the most difficult procedures. You need to completely disassemble the machine, remove the tank and replace the bearings + oil seal. The cost of service work is from 4,000 to 7,000 rubles, plus spare parts (1,500–3,000 rubles). If the machine is older than 7 years, it is often cheaper to buy a new one.

The oil seal is usually replaced along with the bearings, since it also wears out. If you replace only the bearings, the new oil seal can quickly fail due to play.

Repair cost comparison

Breakdown	Cost of spare parts (₽)	Cost of work (₽)	Difficulty of repair
Clogged drain filter/pipe	0 (cleaning)	0–500 (if you call a specialist)	⭐ (you can do it yourself)
Drain pump malfunction	1 200–2 500	1 500–3 000	⭐⭐ (need access to internals)
Worn/broken drive belt	500–1 500	800–1 500	⭐ (replacement in 15 minutes)
Tachometer failure	600–1 200	500–1 000	⭐⭐ (need to get to the engine)
Wear of bearings + oil seal	1 500–3 000	4 000–7 000	⭐⭐⭐⭐ (complete disassembly of the machine)

Frequently asked questions (FAQ)

The Indesit machine does not spin, but the water drains - what should I do?

If the water drains but the drum does not rotate during the spin cycle, check:

• 🔗 Drive belt - it may have fallen off or torn.
• 📊 Tachometer — if it is faulty, the machine “does not see” the revolutions.
• ⚙️ Engine — check the windings with a tester.
• 🧺 Drum overload - take out some of the laundry and try again.

Also make sure that the “No spin” mode is not activated on the panel (the button with a crossed out 🌀).

Why doesn't Indesit spin at high speeds, but works at low speeds?

This is a typical sign bearing wear or loose drive belt. At low speeds (400–600 rpm), the drum can still rotate, but at 1000–1200 rpm, imbalance or slipping occurs.

Also check:

• 🔧 Attaching counterweights - if they are loose, the machine will vibrate strongly.
• 🧲 RPM sensor - it can only operate at low speeds.

How to reset the error on Indesit if it does not turn off?

To reset an error (for example, F05, F11 or F02), do the following:

1. Unplug the machine for 10–15 minutes.
2. Turn on and select the program Drain (if any).
3. After draining the water, start the program Cotton 60° without underwear.
4. If the error persists, try holding the button Start/Pause 5–10 seconds.

If resetting does not help, then the problem is hardware (pump, sensor, board).

How much does it cost to repair if Indesit does not press?

The cost depends on the reason:

• 🧹 Cleaning the filter/pipe — free (on your own) or 500–1000 ₽ (master).
• 🔄 Belt replacement — 1,300–2,500 ₽ (with work).
• 💧 Pump replacement — 2 500–4 500 ₽.
• 🧭 Electronic module repair — 3 000–6 000 ₽.
• ⚙️ Replacing bearings — 5,500–10,000 ₽ (the most expensive repair).

If the machine is older than 5-7 years, repairing bearings or the engine may not be cost-effective - it’s cheaper to buy a new one.

Is it possible to use the machine if it does not spin?

Yes, but with reservations:

• ✅ Can be washed in modes without spin (eg "Wool" or "Hand Wash").
• ✅ After washing, drain the water manually through the emergency hose and spin the laundry manually (if the problem is drainage).
• ❌ You can't Ignore the breakdown for a long time - this can lead to more serious malfunctions (for example, engine combustion).