You loaded laundry into the washing machine. IndesitYou chose the standard 1.5 hour mode, but after 3 hours the drum is still spinning and the display is on a mysterious timer? This problem is familiar to many owners of the Italian brand. Prolonged washing is not only annoying, but also increases the consumption of electricity, water, and also wears out the parts of the machine. In 80% of cases, faults are not faulty, but operation errors or clogged filters – they can be eliminated independently in 10-20 minutes.

In this article, we will discuss 7 Key Reasons for Key Reasonswhy Indesit (models) WISL 85, IWSC 5105, EWS 61051 and others) can wash for 4-5 hours instead of the declared 60-120 minutes. You will learn how to diagnose the problem. error-code (e.g., F05, F11) what settings Increase the washing time by 2-3 times without the user’s knowledgeWhen the Master is really called. At the end, a checklist for quick checks and an FAQ with answers to frequent questions.

1. Clogged drain filter is the main reason for “eternal” washing

If the car Indesit It was done 2 times longer, check it first. drain-filter. It is located in the lower right corner behind a small lid (on models). WISL 103 and IWUB 4085 - under the decorative panel. When the filter clogs, the water drains slowly, and the machine is forced to lengthens the rinse and press cyclesto compensate for the low pressure.

How to know if the filter is to blame:

  • 🔍 The machine. long-dumping (bubbling sounds are heard).
  • ⏳ The washing timer “hangs” at the stage of rinsing or spinning.
  • 🚨 There may be an error on the display. F05 (Plum problem)

To clean the filter:

  1. Take the car off the grid.
  2. Substitute the container under the filter (leaks ~0.5 liters of water).
  3. Turn the counterclockwise filter and remove it.
  4. Remove hair, threads, coins and other garbage. Wash it under running water.
  5. Check the pipe behind the filter for blockages (you can illuminate with a flashlight).

Prepare a cloth and a water container

Turn the car off the socket

Remove the filter and flush it.

Check the pipe for blockages

Install the filter back and start the test wash.

⚠️ Attention: If after cleaning the filter, the machine still drains the water slowly, the problem may be in the process of cleaning the filter. sewerage or a pump malfunction. In this case, you will need to clean the siphon or replace the pump.

2. Wrongly selected washing mode: hidden traps

Many users do not even realize that squash Indesit Initially programmed for 3-4 hours. For example:

  • 🧺 Cotton 60°C or Intensive washing - up to 3 hours (including water heating).
  • 🧼 Eco-mode (Eco 40-60) Up to 4 hours (saving energy but increasing time)
  • 👕 Delicate washing or Wool Up to 2.5 hours (slow rotation of the drum).

To speed up the washing:

  • 🔄 Choose modes Fast 30' or Daily 60' (Unless the clothes are heavily contaminated).
  • 🌡️ Reduce the temperature: heating to 60°C takes 20-30 minutes longer than to 40°C.
  • 💧 Turn it off. rinse (button) Extra Rinse), unless this is necessary.

Fast 30 minutes.

Cotton 60°C

Eco-regime

Delicate washing

The other--

⚠️ Attention: If the car Indesit model IWSD 51051 or WISN 82 “Hanges” during the heating stage of water (timer does not go forward), check TAEN. When scale is formed, it can heat water 2 times longer or even turn off for protection.

3. Overload or underload of the drum: how it affects time

Drum overload One of the most common reasons for long-term washing. If you load into the car Indesit (e.g. model) WISL 102 with a maximum load of 6 kg) 7-8 kg of linen, the following occurs:

  • 🌀 The drum can't evenly distribute things, which is why pressing-off (The machine is trying to balance the load.)
  • 💦 Water gets worse between layers of tissue, and the machine adds additional rinsing cycles.
  • ⏱️ The total washing time is increased by 30-50 minutes.

But underload If there are 1-2 T-shirts in the drum, the machine can be used for the same reason. miscalculate the amount of water and start the extended cycle. Optimal loading for Indesit — 70-80% maximum (e.g. 4.5-5 kg for a 6 kg model).

💡

To check the correct loading, put your hand on the drum while washing. If you feel a strong shock or vibration, there is too much laundry. If the drum rotates almost without resistance, not much.

How to avoid problems:

  • 📏 Weigh your laundry before washing (kitchen scales can be used).
  • 🧦 Wash large items (blankets, jackets) separately from small ones.
  • 🔄 If you do not wash a lot of things, choose a mode. Half-loading. (if you have one in your model).

4. Problems with water heating: TEN and scale

If the washing machine Indesit long-warming Or it doesn't heat it at all, it immediately increases the washing time by 40-60 minutes. Two reasons are to blame:

  1. Scaled on the TEN (This is especially true in areas with hard water). The scale layer with a thickness of 1-2 mm increases the heating time by 1.5-2 times.
  2. Faulty TENG or thermostat. If the heater burns, the machine can either not wash in hot water at all, or try to heat it indefinitely.

How to diagnose the problem:

  • 🔥 Touch the glass of the hatch 20 minutes after the start of washing. If it is cold, the water does not warm.
  • ⏳ The wash timer “freezes” during the heating stage (for example, at 15-30 minutes).
  • 🚨 There may be an error on the display. F07 (heating problem)

Decisions:

  • 🧹 Scaling TENG cleansing: Use citric acid (100g per empty drum, mode) Cotton 90°C) or special equipment (Antinakipin, Topperr 3004).
  • 🔧 Replacement of TENIf the heater is burned, it must be replaced (the cost of the part for the Indesit - from 1,200 rubles.
  • 💧 Installation of a magnetic filter (e.g., AquaSchield) for water softening.
How to check the TEN multimeter?

1. Turn the car off the grid and drain the water.

2. Remove the back cover (on most models) Indesit The TEN is located at the rear.

3. Disconnect the wires from the TEN and measure the resistance between the terminals (should be 25-30 ohms).

4. If the device shows "1" (break) or "0" (short circuit) - the TEN is defective.

5. Failure of the water level sensor (pressostat)

A water level sensor (pressostat) tells the machine how much water is dialled into the tank. If he's out of order, Indesit Maybe:

  • 💦 Underwater Laundry is not washed well, and the machine starts additional cycles.
  • 🌊 Water transfusion The time of draining and spinning increases.
  • ⏳ “Hang” at the stage of water collection (Timer doesn't go forward).

Signs of malfunction of the pressostat:

  • The machine. never-wash- although the water's already dialed.
  • Hear that. pump-buzzIt's like he's trying to drain the water.
  • There's an error on the display. F04 or F11.

How to check the pressostat:

  1. Take the car off the grid.
  2. Remove the top cover (unscrew 2 screws from the back).
  3. Find a pressostat (a plastic box with a tube, usually in the top corner).
  4. Blow into the tube: a click should be heard (if not, the sensor is faulty).

The cost of replacing the pressostat in the service center is from 1,500 rubles. (for models) Indesit WISL 82, IWSC 6105). If you have experience in repairing, you can replace it yourself (the detail costs ~ 800 rubles).

6. Failures in the electronic control module

The control module (the board) is the “brain” of the washing machine. If it fails, Indesit Maybe:

  • 🔄 Run programs in a chaotic manner (For example, first squeezing, then washing).
  • ⏳ "Hang on" at one stage. (The timer is not running, although the machine is working).
  • 🚨 Showing random errors (F01, F18).

Causes of failure:

  • ⚡ Power surges In the network (especially for homes with old wiring).
  • 💦 Moisture intrusion on the charge (due to leaks or high humidity in the bathroom).
  • 🕰️ Wear of capacitors (after 7-10 years of operation).

What to do:

  • 🔌 Reboot the car.Turn off the network for 10 minutes, then turn it on again.
  • 🔧 Check the contacts. on the board (sometimes it is enough to clean the oxidized connectors).
  • 💻 Update the firmware (Relevant to electronic display models, for example, Indesit IWSD 61051).

⚠️ Attention: If the problem persists after the reboot, do not try to repair the board yourself - this can lead to a problem. full-out. Contact the service center (repair fee costs 2,500-4000 rubles).

7. External factors: water, electricity, detergents

Sometimes the reason for the long washing lies not in the car, but in external conditions. Check out these points:

Factor. Signs. Decision
Low water pressure The machine takes a long time to gain water, the timer “freezes” at the beginning of the wash. Check the pressure in the tap. If weak - clean the mesh of the filler hose or install the pump.
Unstable tension The machine spontaneously shuts down, resets the programs. Connect. Indesit through a voltage stabilizer (e.g., Resanta ASN-2000).
Poor quality powder Excessive foam, additional rinse cycles. Use powders for automatic machines (in the case of automatic machines)Persil, Tide) and do not exceed the dosage.
Cold water in the pipes The car warms the water longer (especially in winter). Install a flow heater or wash at night (water is warmer).

⚠️ Attention: If you live in a private home with well-wellcheck it out water-content. High iron levels lead to the formation of rusty plaque on the TENS and sensors, which increases the washing time by 30-50%. In this case, the installation of a reverse osmosis filter will help.

💡

Before calling the wizard, check all external factors - in 30% of cases, the problem is solved without repairing the machine.

FAQ: Frequent questions about long-term washing in the Indesit

The machine washes for 5 hours, but the laundry is dirty. What's up?

The problem is probably in filter-hose (the water does not drain completely) or faulty TEN (water doesn't warm) Check it out.

  1. The temperature of the hatch glass 20 minutes after start (should be warm).
  2. A drain filter for debris.
  3. Quality of powder (it may not be suitable for automatic machines).
There's a bug on the display. F05. What does that mean?

Mistake. F05 into Indesit signifier water-flow. Reasons:

  • Clogged filter or drain hose.
  • Faulty pump.
  • A clog in the sewer pipe.

Solution: Clean the filter, check the hose for inflections, replace the pump if necessary.

Can you speed up the washing without changing the mode?

Yes, there are a few ways:

  • Turn it off. rinse (button) Extra Rinse).
  • Reduce the temperature from 60°C to 40°C (unless the laundry is heavily contaminated).
  • Use it. liquid detergent They dissolve faster and reduce the time of rinsing.
Washing machine Indesit I washed it longer after moving. Why?

Probable reasons:

  • Water pressure has changed. (The new house is weaker than the new one).
  • The car is uneven. Vibration increases the time of pressing.
  • Water hardness is different It is faster to form a scale on the TEN.

Solution: Check the machine level (use the building level), clean the filler hose filter, install a water softening filter.

Worth repairing? IndesitIf it washing for 5 hours, or should I buy a new one?

This depends on the reason and age of the car:

  • If the problem is filter, TEN or pressostat (repair costs up to 2 000 rubles), repair is justified.
  • If it's faulty. board (repair from 3 000 rubles) and a car older than 7 years, it is more advisable to consider buying a new one.

Average service life Indesit - 8-10 years. If your car is younger, repairs will be cheaper than buying a new one.