Modern crossover Belgee X50, which is an adapted version of the popular Geely Coolray, is equipped with an advanced engine starting system that may puzzle the driver who gets behind the wheel of this car for the first time. Instead of the usual turning of the key, a button is used here Engine Start/Stop, and the process itself is initiated only when a number of safety conditions and technical parameters of the on-board network are met.
The driver needs to clearly understand the sequence of actions, since the electronics of the Chinese automobile industry are extremely sensitive to the condition battery and correct recognition of the access key. Any deviation from the algorithm, for example, weak pressure on the brake pedal or a discharged key fob, will lead to the starter not working, and a corresponding warning will light up on the dashboard.
In this article, we will analyze in detail the standard algorithm of actions, consider possible causes of failure of the starting system and give recommendations for operation in the winter, when the chemical processes in the battery slow down and the requirements for starting currents increase many times over.
Standard algorithm for starting the engine from a button
The process of activating the power plant on Belgee X50 tied to an intelligent access system PEPS (Passive Entry Passive Start). For a successful start, the electronics must read the key mark, check the position of the transmission selector and confirm that the braking system is ready to move.
First make sure the selector automatic transmission (DCT) is in position P (Parking). Attempting to start the engine in position N (Neutral) is only possible in emergency mode, but for normal starting the lever must be locked in the parking position. Then press the brake pedal all the way down - this is a critical moment, since the pedal travel sensor must send a signal to the engine control unit.
Once the pedal is locked, the ready indicator on the dashboard will light up and the start button will change color. Click the button Engine Start/Stop and hold it until the starter engages. This usually takes less than a second, the system will automatically turn off the starter as soon as the engine speed reaches stable values.
- 🔑 Make sure that the smart key is in the passenger compartment, preferably in the driver’s pocket or in the antenna coverage area (cup holder or armrest).
- 🛑 Press the brake pedal to the characteristic stop, ignoring free play.
- 🟢 Wait for the green indicator on the start button or on the dashboard to light up.
- 🚀 Briefly press the start button without releasing the brake pedal.
⚠️ Attention: If, when you press the start button, the starter does not spin, and the message “Press the brake pedal” appears on the screen, try pressing the pedal with more force. The sensor may be tight or require a deeper stroke to activate.
☑️ Check before start
Starting the engine with a discharged key
The situation when the battery in the key fob is completely dead is standard and is provided for by the design Belgee X50. The car's electronics are equipped with a backup immobilizer reader, which operates on the induction principle and does not require power from the key itself.
To implement an emergency start, you need to find a special place in the cabin where the key is placed. In the X50 model, this reader is often located in the area of the central armrest or in a niche for wireless charging (if the equipment includes it and the key supports the standard, but more often it is just an NFC tag). Place the key flat on the area indicated by the key or wave symbol.
After placing the key in the reading area, the algorithm of actions remains the same: squeeze the brake and press the start button. The system reads the chip through the induction loop and the engine starts. It is important not to hold the key in your hand at this moment, but to place it directly on the reading panel.
Where exactly should I look for the read tag?
Depending on the year of manufacture and the specific assembly, the mark may be located under the carpet in the center armrest recess, in the storage compartment under the center console, or integrated into the logo on the instrument panel. Look for the key or radio wave icon.
After a successful start, it is recommended to replace the battery in the key as soon as possible to avoid a recurrence of the situation. Usually in Belgee X50 A standard CR2032 battery cell is used, but it is better to check the exact type in the instructions or by opening the key case.
- 🔋 Replace the dead battery in the key as soon as possible to avoid problems.
- 📍 Look for the key or antenna logo in the central tunnel area.
- 📶 Place the key tightly against the reader surface for sure contact.
Features of launching in winter
Winter operation of the crossover Belgee X50, like any modern car with a 1.5 liter turbocharged engine, requires a special approach. Low temperatures significantly reduce recoil lithium iron phosphate or lead-acid batteries, increasing the viscosity of the engine oil.
Before starting in severe frost (below -15°C), experts recommend performing a “waking up” procedure for the battery. To do this, turn on the high beam headlights or heated rear window for 10-15 seconds. This will initiate a chemical reaction in the battery electrolyte, slightly increasing its starting ability before applying load to the starter.
After starting the engine, do not immediately give high speeds. System ECU (electronic control unit) itself will raise the speed to warm up the catalyst and stabilize engine operation. However, if the oil temperature is extremely low, the electronics may limit power or prevent stalling by maintaining a high idle speed.
⚠️ Attention: Do not try to start the engine using the “rocking” method or using a pusher. Belgee X50 equipped with a robotic gearbox, and such actions can lead to fatal damage to the mechatronics or clutch.
Use a pre-heater or regular interior heating via a mobile application (if available and connected) to make it easier to start the engine in cold weather and preserve battery life.
If the engine does not catch on the first try, do not hold the start button for more than 10 seconds. Allow the starter and battery to cool and recover for a minute before trying again. This will prevent overheating of the starter windings and deep discharge of the battery.
Start-Stop system and its effect on starting
Owners Belgee X50 often encounter the peculiarities of the start-stop system, which automatically turns off the engine at traffic lights. Many drivers mistakenly believe that the car has stalled or there is a malfunction in the system when the engine stalls by itself when stopping.
To get moving again, in this case you don’t need to reach for the start button. Simply release the brake pedal (or press the gas, depending on the settings and operating mode), and the engine will start automatically. This is the normal operating mode aimed at saving fuel and reducing harmful emissions.
If you want to force this feature to be disabled, there is a button on the center console with an "A" in a circle with an arrow on it. Pressing it deactivates the system until the next full engine start cycle, after which it is activated again by default.
| Parameter | Regular launch | Start-Stop system | Emergency mode |
|---|---|---|---|
| Driver action | Pressing the + Brake button | Releasing the brake | Hold the button for 10 seconds |
| Selector position | P (Parking) | D (Drive) / N | Any |
| Fuel consumption | Standard | Save up to 10% | Increased (warm-up) |
| Indication | Green indicator | Indicator flashing | Red error signal |
The start-stop system on the Belgee X50 is controlled automatically, but can be disabled by a button on the console; restart occurs without driver intervention when the brake pedal is released.
Diagnosing problems with startup failure
If when you try to start Belgee X50 you hear clicks, but the engine does not rotate, or the starter is completely silent, it is necessary to carry out initial diagnostics. Most often the problem lies in the discharged main battery 12V, which powers the on-board network, even if the car itself is electric or hybrid (although the X50 is an internal combustion engine).
Pay attention to the behavior of the dashboard. If, when you turn the key to the “ignition” position (or press the button for the first time without the brake), all indicators go out, the screens blink, or an intermittent beep sounds, this is a sure sign of a critical battery discharge. In this case, you will need to “light it” from another car or use a starting device (booster).
If the electrics behave normally, they light up brightly, but the starter does not spin and displays the error “Starting system blocked” or similar, the problem may be with the immobilizer or a software failure. In this case, completely de-energizing the car can help by removing the terminal from the battery for 10-15 minutes to reboot the control units.
- 🔦 Check the cleanliness and tightness of the battery terminals.
- 🔋 Measure the voltage at the terminals (the norm for starting is at least 12.4V).
- 💻 Try to reset the error by removing the battery terminal.
⚠️ Attention: When “lighting” the Belgee X50, strictly observe the polarity of connecting the wires. Car electronics are sensitive to power surges, and an error in connecting the “plus” and “minus” can damage expensive control units.
Owner Frequently Asked Questions (FAQ)
Why doesn't Belgee X50 start even though the battery is new?
If the battery is good, check if the car recognizes the key. Perhaps the battery in the key fob has run out, or the key is located in a radio interference zone (near powerful radiation sources). The reason may also be that the brake pedal is not fully depressed or the hood/door is not closed, which blocks the start of the security system.
Is it possible to push start the Belgee X50?
Absolutely not. The car has a dual-clutch robotic gearbox. Push starting will not cause the engine to start successfully, but may cause severe mechanical damage to the transmission and void the warranty.
How long does it take to warm up the engine in winter?
Modern engines do not require prolonged warm-up in place. 1-2 minutes are enough to reach operating speeds and distribute the oil, after which you can start driving in a gentle mode, without sudden acceleration, until the engine reaches operating temperature.
What to do if the start button does not respond?
Try pressing the button with the side of the key (if it has such a function in the instructions) or bring the key directly to the start button. If there is no reaction, check the fuses responsible for the starting system and on-board network, or contact a service center to diagnose the brake pedal switch.