Installation of a reverse osmosis system Geyser Prestige Home water is a smart move for those who want to drink clean water without buying bottled water. Despite the apparent complexity of the design with many tubes and valves, the process of installation and assembly is available to everyone who knows how to handle a wrench. The main advantage of this model is a modular system where each element can be replaced or serviced independently without calling the wizard.
Before starting the work, it is important to understand that leakiness It's a critical parameter. The slightest mistake when installing sealing rings or insufficient tightening of tsang fittings can lead to leaks. In this article, we will analyze not only the order of assembly of the case, but also the nuances of connecting to the water supply so that your system works for years without failures.
Many users make the mistake of ignoring the direction of water flow indicated on the bulb housings. This leads to rapid breakage of an expensive membrane. The correct sequence of actions described below will help you avoid common errors and immediately start the system in normal operation mode.
Accommodation and preparation of the workplace
Before starting the assembly, it is necessary to decompose all components on a flat surface and check them with the instructions. Standard set Geyser Prestige includes three main modules (pre-filters), a module with a membrane, a post-filter, a storage tank, a mineralizer (depending on the modification) and a set of tubes with fittings. The absence of even one small locking ring can stop the whole process.
Prepare the workplace: Cover the table or floor with a dense cloth or cardboard so as not to damage the plastic cases and not stain them. You will need a wrench to tighten flasks, scissors to trim pipes and a water drain tank. Make sure you have free access to the installation site, as the system requires a certain amount of space under the sink.
Pay special attention to the condition of the sealing rubbers. They must be clean, elastic and without clatters. If you are assembling the system after prolonged storage, it is recommended to lubricate the sealing rings with food-grade silicone lubricant to facilitate the insertion of flasks into the housings.
⚠️ Warning: Before assembly, thoroughly rinse the shells with warm water without the use of chemical detergents to remove the production dust.
Unpack the replacement cartridges, but do not install them inside the flasks for now. First, assemble the skeleton system. Check for a drainage clutch and tap for drinking water. All these items should be on hand for quick assembly.
Scheme of connecting tubes and fittings
The hardest part of assembly Geyser Prestige - is the correct connection of modules with each other using polyethylene tubes. In a reverse osmosis system, water moves along a strictly defined path: from the entrance of cold water through pre-filters to the membrane, then to the tank and through the post-filter to the tap. By mixing the entrances and exits, you will either get a weak pressure or damage the equipment.
The tubes have color markings that correspond to the entrances to the filter housings. It is usually blue (water input), red (tank output), black or green (drainage output) and white (water tap output).
The technology of connecting the tube with the fitting requires accuracy. First, make sure that the end of the tube is cut exactly at a 90 degree angle with a special knife or sharp scissors. Then insert the tube into the fitting to the point (about 15-20 mm) and pull out the locking ring (if it is included in the fixation kit), although in most models geyser Self-clamping fittings are used.
- 🔵 A blue tube connects the inlet tube to the first prefilter bulb.
- 🔴 The red tube goes from the outlet of pure water (module with membrane) to the storage tank.
- ⚫ A black tube connects the outlet of the drainage clutch with the sewer clamping.
- ⚪ A white tube leads from the post-filter to the drinking tap.
When inserting a tube into the fitting, a small effort may be required. If the tube enters too easily, it may not be fully inserted, leading to a leak under pressure. If you hear a characteristic click or feel a stress, the connection is done correctly.
⚠️ Warning: Never bend a plastic tube at a sharp angle. This can cut off the flow of water or cause plastic to rupture over time.
☑️ Checking connections
Sequence of cartridge installation
After the tubes are connected to the housings, it is the turn of installing the filter elements. In the system Geyser Prestige A classic five-step cleaning scheme is used. The first three stages are mechanical and coal filtration, the fourth is reverse osmosis, the fifth is finish cleaning and mineralization.
A mechanical cleaning cartridge shall be fitted to the first bulb (left) PP5 (polypropylene) It retains rust, sand and large suspensions. In the second flask is placed the cartridge with carbon-activated (usually CAC or BAC) which removes chlorine and organic compounds. The third module contains a cartridge of fine mechanical cleaning. PP1 or PP0.5Protecting the membrane from small particles.
The fourth module (central, horizontal) is a case with a reverse osmosis membrane. The membrane is already installed inside, you just need to screw the body into the lid. The fifth module is a post-filter (coal) and, if any, a mineralizer. It is important to observe the sequence, otherwise chlorine from the water supply will quickly disable the expensive membrane.
| No. No. | Type of cartridge | Function | Resource (mo) |
|---|---|---|---|
| 1 | PP5 (Polypropylene) | Mechanical cleaning | 3-6 |
| 2 | CAC (Coal) | Chlorine removal | 6 |
| 3 | PP1 (Polypropylene) | Fine cleaning | 3-6 |
| 4 | RO (Membrane) | Reverse osmosis | 18-24 |
| 5 | MMB (Postfilter) | Taste and smell | 6-12 |
When you are curling, do not make excessive efforts. Carving plastic cases may not withstand the strains. Wrap the flasks with your hand to the point, and then with a key (if it comes with a set) make no more than a quarter of a turn. Too strong a puff can deform the sealing ring, which will lead to leakage.
What to do if the cartridge doesn't fit in?
Sometimes the cartridges can be slightly longer than the standard. In this case, you can carefully cut the lower part of the cartridge mesh with scissors, but not the filter material itself. If the problem is in the height of the bulb, check if the rubber ring is inserted correctly into the groove of the cover.
Installation of the storage tank and crane
A storage tank is a container where a supply of purified water is stored. Before installing the tank, it is necessary to create air pressure in it. Factory pressure is usually 0.5 atm, but for stable operation of the system Geyser Prestige It is recommended to check and, if necessary, to pump up to 0.6-0.8 atm through a nipple at the bottom of the tank with a conventional bicycle pump.
Install the tank in a convenient place under the sink, preferably in a vertical position. On the carving of the tank, wind a plastic valve using a sealing tape (fum tape) or thread. Do not pull over the plastic valve so as not to break the thread. Then connect the red tube from the filter to the tank valve.
Installation of the drinking tap is made on the countertop or in the sink (if there is a special hole). Push the tap tube through the hole and secure the crane with a nut on the underside. The pipe from the crane is connected to the exit of the post-filter (fifth stage).
- 🔧 Check the completeness of the crane: the set should be a nut, a washer, a rubber gasket and a decorative lining.
- 💧 Make sure that the tube going to the tap has no cracks and bends.
- 🔩 Fix the tap firmly so that it does not stagger when dialing water.
If you install a tap on a ceramic sink, use a diamond drill of the appropriate diameter. You need to work at low revs with constant cooling with water, so as not to split the ceramics.
Connection to water and sewage
A cut-in clutch is used to connect to the water supply. Cover the cold water in the apartment, find the pipe going to the mixer, and install a coupling. Drill a hole in the pipe with a diameter drill 6-8 mm through the hole in the clutch. Set a rubber gasket and tightly clamped the clutch with bolts.
The filter inlet tube (blue) is connected to the clutch. Between the clutch and the filter must be a ball valve, which comes in the kit. This will allow you to block the water on the filter without turning off the entire apartment.
A special clamping with a drainage insert is used to connect to the sewer. Choose a place on the vertical section of the sewer pipe (siphon) above the level of the water shutter. Drill the hole, glue the clamps (if it is self-adhesive) or fasten with bolts, and insert the drainage tube to the point.
⚠️ Attention: The drainage tube must enter the sewer at an angle so that the wastewater does not flow back into the filter. The bend of the tube should be above the point of entry into the sewer.
To the drill does not slip when drilling a metal water pipe, stick a piece of paint tape to the place of drilling. This will also help avoid scratches on the chrome surface.
First start and wash the system
The assembly is complete, but you cannot start the system in full at once. Reverse osmosis membranes and carbon filters contain a preservative and coal dust that must be washed away. The first start is made without a tank connection and without a membrane (or with open drainage) for washing pre-filters.
Open the valve on the tank and the tap of drinking water. Slowly open the tap on the cut clutch. The water will start filling the flasks. At this point, carefully examine all connections for leaks. If it drips somewhere, tighten the connection or squash it.
After filling the system with water and air out, close the drinking water tap. Let the system pressurize. The first 2-3 tanks of water (about 20-30 liters) are recommended to drain into the sewer, without using water for food. This is necessary for the complete washing of the membrane from the preservative composition.
Check the drainage. With a closed tap of drinking water and an open tank, water should not flow into the drainage (or drip very rarely, once every few minutes). If the water is pouring constantly - the flow limiter or membrane block is defective.
Typical errors and troubleshooting
Even with careful assembly, problems can arise. One of the common mistakes is the lack of pressure in the system. If the pressure from the tap is weak, check the pressure in the tank. If water is pressed on the nipple of the tank, the tank membrane is damaged, the container needs to be replaced.
Another common problem is filter humming. This may be due to high pressure in the water supply or clogging of the drainage limiter. The crane itself can also buzz if air hits it. You can blow the air by opening the faucet for a few minutes.
If water continues to drip into the drainage when the tank is closed, it may not hold the return valve or the membrane is contaminated. In newer systems, it is often a sign of factory defect or damage during transportation. Check the integrity of all seals again.
- 🛠 Weak pressure: Check the pressure in the tank and the condition of the prefilters.
- 💧 Constant drain to sewer: Check the flow limiter and membrane.
- 🔊 Noise at work: check the pressure in the mainline and the lack of air in the system.
Regular replacement of prefilter cartridges (every 3-6 months) prolongs the life of the membrane by 2-3 times, saving you money on expensive components.
Frequently Asked Questions (FAQ)
How often should I change cartridges in Geyser Prestige?
Pre-cleaning cartridges (1-3 steps) and post-filter (5 steps) are changed every 6 months. The reverse osmosis membrane lasts from 1.5 to 2.5 years, depending on the quality of the source water and the volume of consumption. The mineralizer is changed along with the post-filter.
Why does the filter take so long to get water into the tank?
The time to set a full tank (8-10 liters) can take from 40 minutes to 1.5 hours. This is normal for reverse osmosis systems. If the time exceeds 2-3 hours, check the pressure in the plumbing (normal from 3 atm) and the condition of the prefilters.
Can I install a filter in an unheated room?
Absolutely not. At temperatures below +5°C, the water in the flasks can freeze, which will lead to rupture of the housings and damage to the membrane. It is also not recommended to install under direct sunlight to prevent water blooming.
Do I need to boil water after the filter?
Water after reverse osmosis is purified and safe, boiling is not required. However, since almost all minerals have been removed from the water, it is recommended to use water after a mineralizer or add minerals artificially.